What Type of Grease is Used to Lubricate the Fulton Round Snap-Ring Swivel Marine Jack

Question

Question:

what should i lube jack with

asked by: Matt C

0

Expert Reply:

I spoke with my contact at Fulton and he said the Fulton Snap-Ring Swivel Jack, # FTJ12000101, can be lubricated with any general-purpose grease like our LubriMatic Lithium Grease, # L11316.

You can remove the cap at the top of the jack and put the grease in the cap. The grease will have to be gravity fed to the bottom of the tube since there is not an easy way to apply the grease down to the bottom.

expert reply by: John H

0

Answer 1

The Fulton Bolt-Thru Swivel Marine Jack part #FXP10 which has a 1,200 lb weight capacity is the best option we have to replace the existing 800 lb model you have now. Unfortunately, we don't have any jacks which use the same bracket you have now…

view full answer...

Answer 2

It really looks like you have a Fulton Jack like the part #FTJ120W0301 based on the picture you submitted. The jack portion of the picture matches the jack I mentioned but the bracket on the trailer does look slightly different. Does the tube welded…

view full answer...

Answer 3

The hole in the bracket of the Fulton 1200 lb Snap Ring Swivel Jack #FTJ12000101 is 2.55 inches in diameter to accommodate the 2-1/2 inch diameter flange on the trailer mounted bracket that the snap ring attaches to. The 2-1/2 inch diameter flange on…

view full answer...

Answer 4

I was not able to find the same bolt pattern you said your older Fulton jack has for your Ranger boat trailer, but I may have a solution that will work for you. I recommend going with a jack like the Fulton Round, Snap-Ring Swivel Marine Jack, part…

view full answer...

Answer 5

There isn't a super strict maintenance schedule for lubing the Fulton Round, Snap-Ring Swivel Marine Jack #FTJ12000101 with the zerk fitting it has on the tube of the jack, but I'd recommend doing it twice a year or whenever you feel like the…

view full answer...

Answer 6

We offer four different 1/2-inch diameter plunger pins that are shown on the linked page. Two of the four are bent pins, parts #F0933307S00 and #PLGPIN-12 that you referenced. I went to our warehouse and measured both of these. While they are not…

view full answer...

Answer 7

I pulled both products from the warehouse to measure and compare for you. The Dutton-Lainson pin #DL22454 (unlike the page photo) has the cotter pin hole in line with the handle and is 1-7/16 inches from the end to the cotter pin hole center. The…

view full answer...

Answer 8

The plunger pins are usually specific to the brand of jack and usually are not interchangeable. Unfortunately, without knowing the manufacturer and model number of your existing jack, I cannot say with certainty that the pin will work for you. I have…

view full answer...

Answer 9

The Replacement Plunger Pin Assembly for etrailer and Ram Jacks #PLGPIN-12 has a 1/2" diameter, measures 5" long, and the straight part measures 2-1/2" (see attached photo). We used to carry the Shelby jacks back in the day when they…

view full answer...

Answer 10

I am not totally sure which jack you are referencing but most jacks are designed to be lubricated with white lithium grease like part #L11354.

view full answer...

Answer 11

From what I could find it looks like your 122R (red) and 122Y (amber) lights measure 3.75" x 1.70" x .81". We don't have any replacement lense directly for the GLO-BRITE lights but we do have some similar lights that you could use…

view full answer...

Answer 12

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

What Type of Grease is Used to Lubricate the Fulton Round Snap-Ring Swivel Marine Jack

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching