36 inch Long Handle Extension for Valterra Bladex RV Valve

Question

Question:

Will this Bristol, LaSalle extension work with a Valteera Bladex valve? Thanks

asked by: Olin B

1

Helpful Expert Reply:

We have a 36 inch long handle extension designed for Valterra Bladex valves part # TX36HPB which comes with the handle too so it would be your best option.

expert reply by: Jameson C

1

Answer 1

Yes, the handle of the Valterra waste valve, part #T1003VP, does unscrew so it can be replaced or extended. We have several different lengths of extended rods that fit: 8 inches, #TX8HPB 9 inches, #TX9HPB 24 inches, #TX24HPB 32 inches, #TX32HPB 36…

view full answer...

Answer 2

Hey Travis, congrats on the new 2024 Jayco Flight 284BHS! Your travel trailer looks to have a GVWR of 7,950 lbs so I recommend going with the Equal-i-zer Weight Distribution w/ 4-Point Sway Control #EQ37121ET and pairing it with the Shank…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

Hey Mark, so the correct Blue Ox base plate kit to use with the Blue Ox Ascent tow bar part #BX4375. is the part #BLU53FR. For lighting you can use #C96JR, and not have to worry about cutting into the taillight housing as this plugs inline with the…

view full answer...

Answer 5

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 6

Thank you so much for the info and the pictures! According to my research it looks like your Cummins Onan RV Generator uses a 3/8" NPT Female fitting so you'll need a hose like part #100040-144-MBS. I have attached a link to all of our hose…

view full answer...

Answer 7

An E5 error for an Atwood 1361 AC unit would indicate a compressor overload. Most likely the start capacitor for your fan is shot and needs to be replaced and without the fan blowing your compressor is cooling air and having nothing to force it down…

view full answer...

Answer 8

The Replacement Hydraulic Pump Motor for Lippert Hydraulic Power Unit #LC167576 is designed to replace a broken motor from the Lippert Hydraulic Power Unit with 2-Quart Pump Reservoir Kit for RV Slide-Out IRC System #LC141111. We'd have to know…

view full answer...

Answer 9

Yes we've confirmed with both Valterra and LaSalle Bristol that the threads of both of the extension rods are the same 1/4 inch size. So the #34466SP1112 that you referenced which is 12 inches long would work well for you.

view full answer...

Answer 10

Yes, the Lippert Replacement Hydac Cartridge Valve for RV Slide-Out Hydraulic Pump #LC177094 is a valve that can be used with your Lippert Replacement Hydraulic Power Unit with 2-Quart Pump Reservoir Kit for RV Slide-Out IRC System #LC141111. I have…

view full answer...

Answer 11

Since the part number you have is 906900427 the correct part you are looking for is the Replacement Lippert Touchpad and Harness for Kwikee Level Best Hydraulic Leveling System - Winnebago #LC48UD which we have confirmed with Kwikee/Lippert.

view full answer...

Answer 12

The correct replacement for your Klauber K01431B300 slide-out motor is the Replacement Motor Assembly for Lippert RV Slide-Outs - Klauber A-300 Model #LC157511.

view full answer...