Baby Moon Cover that Could Possibly Fit Conventional Style Wheel

Question

Question:

I am trying to fit a smooth baby moon onto these old wheels they are 14s I think and I think these bumps will allow a moon Does this sound right I think I then would need to hole saw a circle for the bearing buddy Can you help me research this

asked by: Paul

0

Expert Reply:

If you measure the diameter of where the baby moon cover needs to install I can tell you if the # AM90086 would fit or not. If the diameter happens to be 9-1/4 inches then this cover would fit. You'd have to determine the size hole saw you'd need to get the Bearing Buddy to fit through though.

expert reply by: Jameson C

0

Answer 1

Based on the dimensions you mentioned needing for a baby moon cover the #AM90086 that you referenced would be the correct fit. I attached a review video for more info on it as well.

view full answer...

Answer 2

Measure the diameter of the wheel you have where a baby moon cover would fit and then compare that to the picture I attached. If the diameter is 9-1/4 inch the part #AM90086 would fit. If you have something different let me know and I'll see what…

view full answer...

Answer 3

We do have some towing mirrors that are confirmed to fit your 2016 Nissan Frontier, but unfortunately the CIPA Custom Towing Mirrors #CM10200 that you referenced are not compatible. Instead I recommend going with the CIPA Universal Fit Dual-View…

view full answer...

Answer 4

The measurement that you will want to take is the outer diameter of the inner ring and the outer diameter of the inner ring with one of the tabs (see photo). You will also want to count the bolt holes on the wheel and know the wheel diameter. The…

view full answer...

Answer 5

I would be happy to help, but when I looked up your 2017 Gulf Stream Vintage Cruiser I was unable to confirm the wheel size. The Americana Baby Moon Trailer Wheel Center Cap - Chrome-Plated Steel #AM90086 you were looking at fit 13" - 15"…

view full answer...

Answer 6

Your 2020 Gulf Stream Vintage Cruiser 19ERD has 14" 5 lug conventional wheels, and will need the Americana Baby Moon Trailer Wheel Center Cap #AM90086.

view full answer...

Answer 7

I was able to reach out to Americana and they informed me that the Baby Moon Trailer Wheel Center Cap - Chrome-Plated Steel - Qty 1 #AM90086 is roughly 3" deep, so they should work with your spindles- but it is going to be a tight squeeze.

view full answer...

Answer 8

The Americana Baby Moon Trailer Wheel Center Cap - Chrome-Plated Steel - Qty 1, part #AM90086, is installed with snap-in installation. Your wheel should have three hubs. If you line up two of the three hubs with your hub cap, you should be able to…

view full answer...

Answer 9

Hi Rene; I'm sure it's frustrating to have the mirror fall off, and while there are only universal towing mirrors for your 2016 Nissan Frontier, there are better ones than the clamp-on (which I also do not like). I would definitely go with…

view full answer...

Answer 10

I do have a solution for you but there have actually never been any custom towing mirrors made for a Nissan Frontier and so I would be surprised if any ever come out for your 2019 Nissan Frontier. Since this is the case I recommend using the K-Source…

view full answer...

Answer 11

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 12

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Baby Moon Cover that Could Possibly Fit Conventional Style Wheel

Product Page this Question was Asked From

Continue Researching