Why Doesn't CE Smith Stake Pocket # CE45004G Have Bottom

Question

Question:

Do you have any stake pockets that have a bottom lip to keep the 2x4 from falling all the way down. The CE45004G does not have this lip as far as I can see from your pictures

asked by: Larry A

0

Expert Reply:

Since most stake pocket applications involve letting the board fall as far as it can into the pocket and a horizontal board attached to the 2x4 providing how it stops none of the stake pockets we offer like the # CE45004G have bottoms.

expert reply by: Jameson C

0

Answer 1

I went out to the warehouse and pulled a CE Smith Stake Pocket, #CE45004G, to take some measurements. The dimensions listed on the product page are correct. The opening is 3-1/2 inches wide by 1-1/2 inches deep. A lumber industry standard 2x4…

view full answer...

Answer 2

I do have an option for you but the Rack'em Heavy Duty Stake Pocket for Flatbed Truck or Trailer part #PK-BSP does require the stake to be tapered at the bottom. I recommend CE Smith Stake Pocket for Flatbed Truck or Trailer - Galvanized…

view full answer...

Answer 3

We have exactly what you need, check out the CE Smith Stake Pocket for Flatbed Truck or Trailer #CE45004G. These are the metal brackets that once you attach to a trailer will allow you to build a sidewall for you trailer. The pocket accepts a 2x4.…

view full answer...

Answer 4

There are two Curt 5th wheel service kits. The Curt #16125-SK3 kit is designed specifically for the Curt #C16125 hitch. The Curt #C45UR kit is for most other Q-series hitches. Unfortunately, Curt does not sell the grommets individually.

view full answer...

Answer 5

We carry a number of stake pockets and you can choose the correct one for your application in terms of size and weld or bolt on. The bolt-on option is the CE Smith Stake Pocket #CE45004G which is 3-1/2" long x 1-1/2" wide x…

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 9

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 10

To determine the size of the hub assembly you need to purchase you have to determine which bearings are in the old assembly. If the old assembly has L44649 inner bearings, you would use the hub you chose #8-258-5UC1. If the inner bearings are marked…

view full answer...

Answer 11

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 12

A BT8 spindle would have a diameter of .99 of an inch where the bearings would both install and would have a diameter of 1.24 where the great seal would ride. That would require a hub part #AKIHUB-440-2-1K for an idler hub. A BTR spindle would have…

view full answer...

Why Doesn't CE Smith Stake Pocket # CE45004G Have Bottom

Product Page this Question was Asked From

Continue Researching