Spanner Wrench Replacement for Trailer Valet XL

Question

Question:

Hi. I am looking at a used Trailer Valet XL with missing connection hardware and spanner wrench - see attached photo. Do you sell the spanner wrench and attaching square extensions? How much?

asked by: Hung N

0

Expert Reply:

We have the replacement spanner wrench for the Trailer Valet XL with the part # TVXLTT. We don't have the bracket that runs from the hitch ball base to the jack leg though as that's not used on current versions.

expert reply by: Jameson C

0

Answer 1

If I had to guess the valve stem is bad and if you put pressure on it leaks. What you'd want to do is replace the inner tube with the part #TVIT.

view full answer...

Answer 2

The best recommendation I can make would be to have the trailer attached to a tow vehicle so that the jack can be unsupported and you can easily access it. After that you'll need to unbolt the wheel assembly from the jack. Remove the valve stem…

view full answer...

Answer 3

I spoke to my contact at Trailer Valet to get specifics on the tires supplied with Trailer Valet Swivel Jack and Trailer Mover, part #STC-V211. The dual tires measure approximately 9 inches by 2-1/2 inches (this will vary slightly depending on tire…

view full answer...

Answer 4

Yes, the Trailer Valet XL Trailer Dolly #TVXL25 does come with solid rubber tires. We carry the replacements here with part #TVXLSR if you ever need to replace one, but Trailer Valet did upgrade from the pneumatic tires for this superior design.

view full answer...

Answer 5

Trailer Valet XL Trailer Dolly #TVXL25 will be able to move your trailer at the near 90 degree angle and up the incline of the driveway. The dolly has 2 gears and you will likely find that the low speed, 27 to 1 ratio will make it easier on you…

view full answer...

Answer 6

I went to the warehouse and checked out the Replacement Drill Attachment for Trailer Valet XL Trailer Dolly, part #TVDA for you. The adapter will work best with 1/2 inch 18V drills. This adapter will work with #TVXL2 and #TVXL25 and also the…

view full answer...

Answer 7

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 8

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 9

You will need the Red LED Trailer Clearance or Side Marker Light #328-K-52 or Amber LED Trailer Clearance or Side Marker Light #328-K-51 for your 2018 Forest River Sunseeker motorhome. These lenses have the same Top Command SAE-AP2-16 markings on the…

view full answer...

Answer 10

The 40 amp fuse for your 2006 Chevrolet Silverado tow package is used for the 12 volt battery charge circuit. This fuse is located toward the front of the underhood fuse box closest to the front auxiliary positive post (see photo). There may be a…

view full answer...

Answer 11

On a 2005 Chevy Silverado 1500, If you are facing the front of the truck looking at the power distribution box, there will be a post at the back left side and a fuse slot near it. It is that fuse slot that you will install a 30 amp fuse. I have…

view full answer...

Answer 12

The number you provided, "7753400" is a patent number which corelates to the Equalizer for E-Z Flex Suspension part #013-144-03. This is for a single equalizer but if you need the entire kit it's the Dexter E-Z Flex Suspension Kit part…

view full answer...

Spanner Wrench Replacement for Trailer Valet XL

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching