Minimum PSI for Air Lift LoadLifter 5000 Ultimate Air Bags On a 2016 Ford F-350

Question

Question:

I have a 2016 F350 with AL 5000 ultimate with jouncefoot What is the safest minimum pressure to run on a empty truck?

asked by: James H

0

Expert Reply:

The minimum psi for the Air Lift LoadLifter 5000 Ultimate Air Helper Springs part # AL88396 while installed on your 2016 Ford F-350 is 5 psi which is to ensure the airbags do not become deformed.

expert reply by: Conner L

0

Answer 1

Although there is not a specific psi for an unloaded Ford F-250 with the Air Lift LoadLifter 5000 Ultimate Air Helper Springs #AL88396 you do need to make sure you have enough air pressure to maintain a level ride height and there is a minimum of 5…

view full answer...

Answer 2

I'd set aside an afternoon/evening to install the Firestone suspension kit part #F2597 on your truck. The install isn't anything crazy so it shouldn't be too hard at all as long as you have basic tools. You can view the entire install…

view full answer...

Answer 3

Using a union tee like the part #AL21838 would be a great way to simplify inflating the bags of the Air Lift kit part #AL88396. This will allow you to inflate both bags at one time with one valve stem and will give both of the bags equal air…

view full answer...

Answer 4

All you would need to install the Air Lift LoadLifter 5000 Ultimate Air Helper Springs with Internal Jounce Bumpers #AL88396 on your 2014 Ford F250 with a 3-1/2 inch lift kit is the correct lift spacer kit. For that you would need the spacer kit part…

view full answer...

Answer 5

If your Air Lift System similar to the Air Lift LoadLifter 5000 Ultimate Air Helper Springs with Internal Jounce Bumpers #AL88396 is leaking by the brass you should: - Check the threaded connection by tightening the swivel fitting another ½…

view full answer...

Answer 6

For your 2019 Ford F350 whether it is 4WD or 2WD will make a difference. If you have the 2WD then I recommend the Air Lift LoadLifter 5000 Air Helper Springs - Rear Axle #AL57391. If you have the 4WD I recommend #AL57399. These options are confirmed…

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 9

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 10

Since the pin weight of your camper is 2.1k, I recommend going with the LoadLifter 5000 opposed to the 7500. While technically there is not reason you couldn't use the 7500 kit, it really is not necessary for a camper like yours. Generally the…

view full answer...

Answer 11

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 12

It sounds like the purpose of getting the air helper spring would be to counteract the 1 inch compression you're getting in your rear suspension caused by the pin weight of your 5th wheel. If that's the case, I believe that the AirLift 5000…

view full answer...