How Long is 7-Way Harness of etrailer Ram Jack EJ-3527-BBX

Question

Question:

Hi, Was wondering how long the wiring is on the 7way plug for lighting up the area. I ask this, as I was wondering of this can be used when connecting to the trailer, not just for connect and disconnect. Thank you,

asked by: Geary

0

Expert Reply:

The length of the 7-way harness that comes with the Electric Jack w/ Footplate and 7-Way Plug # EJ-3527-BBX that you referenced is 57 inches. I attached a review video for this jack for you to check out as well.

expert reply by: Jameson C

0

Answer 1

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 2

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 3

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 4

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 5

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

The Lippert 2420801 hub is an 8k hub with an 8 lug bolt pattern so for a replacement you'd just need the part #8-285-10UC3-A.

view full answer...

Answer 8

We do carry the 33" Ark Stabilizer Jack that you are looking for with part #ARK77FR. I was able to track down a few drawings that you should find helpful. These are for the 30" #ARK94FR and the 24" #ARK34FR Stabilizer jacks. I'm…

view full answer...

Answer 9

I apologize for the confusion. It sounds like you have found some conflicting answers in the past, so I took the liberty to contact Bulldog directly and this is what they said: "The 12k RAM jack has a smaller diameter cross-shaft, therefore the…

view full answer...

Answer 10

I contacted the manufacturer about the lengths for these stabilizer jacks and have included the information they were able to provide me. The Ark Drop Down Corner RV Stabilizer Jacks #ARK34FR are 422 mm (16.6") collapsed and 600mm (23.6")…

view full answer...

Answer 11

Hi Tom, I have two options to replace the electric tongue jack on your Jayco Whitehawk: Option 1: Electric Jack w/ Footplate #EJ-3520-BBX. This jack is going to be your no-frills 'get the job done' style jack. It has a 3,500lb capacity and…

view full answer...

Answer 12

I went ahead and pulled this Replacement I-Beam Jack Bracket #LC349975 from our warehouse to measure. I have attached the dimensions below. Hope this Helps.

view full answer...