Can MaxxAir II RV and Trailer Roof Vent Cover Fit on Hengs Trailer Roof Vent

Question

Question:

Will this fit over the over #MA26JR lid on a Heng roof vent with no obstructions?

asked by: Chris

1

Helpful Expert Reply:

Yes, the MaxxAir II RV and Trailer Roof Vent Cover # MA26JR that you referenced will fit over the standard Heng roof vent you have on your trailer. Due to the height of this (and other similar vent covers) you won't be able to fully open the roof vent but with roof vents the lid doesn't have to be fully opened to get full air flow.

expert reply by: Jameson C

1

Answer 1

The MaxxAir Zero Leak Hardware Kit #MA00-225000 that you referenced is the only such kit we offer. It can be used with vent covers MA00-933066, MA00-933067, MA00-933068, or MA00-933069 which do vary slightly in size. Part #MA00-933066, for example,…

view full answer...

Answer 2

Yes, the SoftStartRV Soft Start for RV AC Units #SSR54FR will work on your Coleman-Mach 15 air conditioner. We actually have an installation video that shows it being installed on a Coleman-Mach 15 air conditioner, which I have linked below.

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 5

To determine the size of the hub assembly you need to purchase you have to determine which bearings are in the old assembly. If the old assembly has L44649 inner bearings, you would use the hub you chose #8-258-5UC1. If the inner bearings are marked…

view full answer...

Answer 6

A BT8 spindle would have a diameter of .99 of an inch where the bearings would both install and would have a diameter of 1.24 where the great seal would ride. That would require a hub part #AKIHUB-440-2-1K for an idler hub. A BTR spindle would have…

view full answer...

Answer 7

No, the MaxxAir II RV and Trailer Roof Vent Cover w/ EZClip #MA26JR that you referenced does not come with a bug screen.

view full answer...

Answer 8

The correct big screen for the MaxxAir II RV and Trailer Roof Vent Cover part #MA26JR is the Replacement Bug Screen for MaxxAir II RV and Trailer Roof Vent Covers part #MA10-20121.

view full answer...

Answer 9

No the MAXX AIR II Vent Cover #MA86JR that you referenced does not come with a bug screen built into it. Just the screen is not available as it does not separate.

view full answer...

Answer 10

It sounds like there is an electrical short on your trailer wiring that is activating your left rear brake assembly and that is why the brake continues to drag and get hot. Since you have swapped the brake assembly out and still had the problem you…

view full answer...

Answer 11

Hey Charles, yes the K-Source tow mirrors part #KS69NQ are compatible with the BSDS camera system and BLIS of your 2024 Ford F-150.

view full answer...

Answer 12

Yes, the Replacement 7" Monitor #FR47FR will indeed work with the Furrion Vision S Camera system already installed on your camper. It sounds like you are also going to need the Replacement Monitor Power Cable #C-FOS07TAPK-006 and the Replacement…

view full answer...

Can MaxxAir II RV and Trailer Roof Vent Cover Fit on Hengs Trailer Roof Vent

Product Page this Question was Asked From

Continue Researching