Replacement Grease Seal For 15192TC Grease Seal On Older Utility Trailer

Question

Question:

I have late 90s utility trailer single axle venture technologies mesh landscaping with ramps trailer. I have the grease seal out - it is rubber with solid core. double lipped with O ring inside. hard to see number but I believe 15192TC - it is not the one I see on your website. 1.5 inside and 2 on outside

asked by: Joel M

0

Expert Reply:

To replace the 15192TC double lipped grease seal in your hub, I recommend grease seal pair # RG06-020 which has an inside diameter of 1.5 and outside diameter of 1.987 which is confirmed as a replacement for the 15192TC. They are the closest seals we carry in dimension to yours.

expert reply by: Heather A

0

Answer 1

The correct replacement for Atwood 7" x 1-3/4" Hydraulic Drum Brakes is the Dexter Hydraulic Trailer Brake Kit part #23-398-399. If you are having trouble removing the old brakes, I recommend applying heat but you can cut the nuts…

view full answer...

Answer 2

If the spindles on your Reliable 2,700 pound axle are straight (same diameter in both bearing locations) then that indicates that it uses L44649 inner and outer bearings but if the spindles are tapered (inner bearing surface diameter is larger than…

view full answer...

Answer 3

Based on the number and dimensions you listed the correct grease seal you need is the part #RG06-020 as this cross references to what you have and matches the dimensions.

view full answer...

Answer 4

I was not able to find confirmed dimensions for the seal part 16192TC but we do have many grease seals and it is possible to find a replacement based on the dimensions. The seal inner diameter corresponds to the diameter of the spindle; the outer…

view full answer...

Answer 5

I've actually answered a similar question on this before and found: In my research I found that the grease seal you are looking for could have an inner diameter of either 2.24 or 2.12 inches and an outer diameter of 3.37 inches when measured…

view full answer...

Answer 6

Thank you for the information! It sounds like you have a BTR spindle which means you need a grease seal that has a 1.500" ID and 1.987" OD. For this we have part #10-9 for a single seal or part #RG06-020 for a pair of seals.

view full answer...

Answer 7

I can help you determine how to figure out the grease seal you need, although a trailer spindle won't have an inner and outer seal; the Timken bearings you referenced seem to be automotive bearings and there wasn't a cross-reference…

view full answer...

Answer 8

I went out to the warehouse and found that the TruRyde Grease Seals #RG06-020 that you referenced are 1/4" thick. If the ID and OD are correct for your application then this is the correct set of grease seals for you as those are the…

view full answer...

Answer 9

In order to find the correct replacement hub and spindle you will need to know the capacity of your axle along with the bearings you currently have. In order to find the size of the bearings you can look for part numbers on your existing bearings.…

view full answer...

Answer 10

You can verify that the 10-19 grease seal included in Bearing Kit #BK2-100 is the correct one for your spindles by taking two measurements. First you want to measure the rear hub bore where the seal is inserted. The seal's outer diameter…

view full answer...

Answer 11

The inner and outer bearings should have a part number stamped on them. The grease seal typically has a number stamped on the rubber, as well. If you cannot find the number on the seal, the inner diameter of the seal can be used to find a…

view full answer...

Answer 12

Your math is correct in your trailer weight load example. If a fully-loaded tandem axle trailer weighs 4000-lbs then each of the 4 tires will bear 1/4th of that load, or 1000-lbs. In this case a tire rated for 1300-lbs would provide a good safety…

view full answer...

Replacement Grease Seal For 15192TC Grease Seal On Older Utility Trailer

Product Page this Question was Asked From

Continue Researching