Replacement Grease Seal for 1-1/16 Inch Straight Spindle

Question

Question:

Please help me. What axle seal would you recommend for a straight 1 1/16 axle spindle with 1,98 o.d. ? I removed the bearing but it doesnt have a number on it. The trailer is a 1999 Loadstar gross weight 1000 pounds. Thank you.

asked by: Richard F

1

Helpful Expert Reply:

Thank you for the information!

It sounds like you have a BTR spindle which means you need a grease seal that has a 1.500" ID and 1.987" OD. For this we have part # 10-9 for a single seal or part # RG06-020 for a pair of seals.

expert reply by: Jon G

1

Answer 1

To replace the 15192TC double lipped grease seal in your hub, I recommend grease seal pair #RG06-020 which has an inside diameter of 1.5 and outside diameter of 1.987 which is confirmed as a replacement for the 15192TC. They are the closest seals…

view full answer...

Answer 2

I can help you determine how to figure out the grease seal you need, although a trailer spindle won't have an inner and outer seal; the Timken bearings you referenced seem to be automotive bearings and there wasn't a cross-reference…

view full answer...

Answer 3

I went out to the warehouse and found that the TruRyde Grease Seals #RG06-020 that you referenced are 1/4" thick. If the ID and OD are correct for your application then this is the correct set of grease seals for you as those are the…

view full answer...

Answer 4

To pick out a replacement grease seal you will need to measure the diameter of the spindle where the grease seal rides with a digital or dial caliper and then need to measure the hub bore where the current seal rides. With those two dimensions we can…

view full answer...

Answer 5

There is not an issue with installing the grease seal #9103309 you were looking at 1/16" below the face of the hub. It will still seal against the grease seal surface on your axle, though you will want to make sure to not force the seal down to…

view full answer...

Answer 6

When installing a seal at the back of a hub the outer part of the seal will need to be flush with the hub. I have linked a video that should help. You could watch the whole video or fast forward to the 1 minute, 50 second mark to see the seal…

view full answer...

Answer 7

The inner and outer bearings should have a part number stamped on them. The grease seal typically has a number stamped on the rubber, as well. If you cannot find the number on the seal, the inner diameter of the seal can be used to find a…

view full answer...

Answer 8

While your spindle may have a diameter of 1-1/16 inch where the bearings ride the diameter where the threads are is actually 1 inch like what the part #5-23 that you referenced assuming you have a standard trailer spindle which it sounds like you…

view full answer...

Answer 9

Since Demco uses 3,500 drum brake assemblies part #DMSB24429M and #DMSB24428M what you'd need is similar 3,500 electric brake assemblies like the etrailer part #AKEBRK-35L-SA for the left hand side and #AKEBRK-35R-SA for the right hand side. To…

view full answer...

Answer 10

If your old axles have a 5 bolt brake flange the assemblies like Dexter Electric Trailer Brake Assembly - 12" - Left Hand - 6,000 lbs part #23-105 or Dexter Electric Trailer Brake Assembly - 12" - Right Hand - 6,000 lbs part #23-106 will…

view full answer...

Answer 11

The old version of the #HBA-CAM used 4 wires, but the product was updated awhile back and now uses only two wires as shown in the photo on the product description page. The white wire from the HBA-CAM would tap into the white ground wire and the blue…

view full answer...

Answer 12

The 40 amp fuse for your 2006 Chevrolet Silverado tow package is used for the 12 volt battery charge circuit. This fuse is located toward the front of the underhood fuse box closest to the front auxiliary positive post (see photo). There may be a…

view full answer...

Replacement Grease Seal for 1-1/16 Inch Straight Spindle

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching