Replacement Front Cover for Solera Power Awning Idler Head

Question

Question:

front cover for a solera powered awning on a 2018 Thor Four Winds, 24ft class C motorhome - I knocked the cover off of the awning and cannot find any part number - it is a 16 ft awning - can you help?

asked by: Marie B

0

Expert Reply:

We do have replacement covers for your Solera Power Awning idler head such as part # LC672052. What you need is the Solera Awning Plain Idler Head Front Cover # LC289566.

If you have an idler head with a speaker such as Solera Power Awning Speaker Drive Head # LC342149 what you need is the Replacement Cover for Solera Power Awning Speaking Idler Head - Front # LC354189.

expert reply by: Kyle S

0

Answer 1

Thank you for the picture, I can see the pin is bent rendering your solera head shaft inoperable even though you tried bending it back. Unfortunately, the only fix would be to completely replace the head as this part isn't currently…

view full answer...

Answer 2

Without knowing exactly which awning assembly you have-either 63" or 69"-there could be a number of parts that you might need. You can get just the pitch arm assembly with the Replacement Pitch Arm Assembly for Solera 69"…

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 8

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 9

When installing an awning like the Solera Smart Arm 12V Power RV Awning #LC517486, the arms will be secured to the wall framing. When the awning extends there will be quite a bit of leverage, so it is important to mount the awning to an area where…

view full answer...

Answer 10

Yes, I have listed for your below the roof rack systems from Rhino-Rack, Thule, and Yakima that will fit the RetraxPRO XR Hard Tonneau Covers like part #RTT-80243 for your 2019 Ram 1500. Rhino-Rack Vortex Crossbar System part #RRVA180B-RRRLT600…

view full answer...

Answer 11

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Answer 12

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...