Brake Controller Wiring Location in the Cab of a 2010 GMC Sierra 1500

Question

Question:

I have a 2010 GMC Sierra 1500 Z71. It has the special equipment towing package I want to install the brake controller but CANNOTfind the wires which are supposed to be in behind the steering column Can u give me an idea where they are????? Many thanks Dennis

asked by: Dennis M

0

Expert Reply:

I was unable to find a guide for your specific vehicle, however I have included a link to a video for a 2008 GMC Sierra that shows the brake control wires under the dash below the steering column and down by the brake pedal. The wires will be bundled up and there may be a white tab around them. Let me know if this is not helpful and we will do further research to try to help you find these wires.

The video shows the technician pulling the wires from the brake pedal area at the 1 minute and 20 seconds mark. I have also included a link for an article of brake controller installation that includes a picture of the location of the brake controller wires location on the 2010 GMC full size trucks.

expert reply by: John H

0

Answer 1

On your 2010 GMC Sierra no plug is present under the dash for installing a brake controller, but the needed wires are already run. You will connect the brake controller wiring with the vehicle wiring already present under the dash. I attached a help…

view full answer...

Answer 2

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 3

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

For sag from towing a trailer the best recommendation I can make is actually a weight distribution system. Suspension enhancement will help level your truck while towing. But the advantage to a weight distribution system is that it levels the vehicle…

view full answer...

Answer 7

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Answer 8

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 9

Choosing the right height setting for your 5th wheel hitch is a combination of a few different variables. First of all you want your towing setup to be as level as possible. With your Montana High Country 340BH level you will want to measure from the…

view full answer...

Answer 10

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 11

It sounds like the purpose of getting the air helper spring would be to counteract the 1 inch compression you're getting in your rear suspension caused by the pin weight of your 5th wheel. If that's the case, I believe that the AirLift 5000…

view full answer...

Answer 12

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...