How Does Stand Off Brace SPN416 Attach to RV Ladder and RV Wall

Question

Question:

How does the stand-off brace hold in place?

asked by: Robert W

1

Helpful Expert Reply:

I attached a picture that shows how the Stand Off Brace part # SPN-416 attaches to both the ladder and the RV wall. Basically a single screw holds the ladder to it and then 4 screws hold it to the RV wall.

expert reply by: Jameson C

1

click to enlarge

Chuck H.

5/24/2020

When the stand-off brace connects to the trailer with the screws, isn’t there some type of gasket or silicone material between the trailer wall and the brace? Thanks

Reply

Chris R.

5/26/2020

The bracket is designed to bolt directly to the trailer wall (without the use of a gasket in between).

Reply

Answer 1

We don't have a diagram of how the stand off of the #LA-401 installs but I did attach the only diagrams we have for this ladder. Basically though the shank of the stand off fits through the mounting bracket and then a screw goes through the…

view full answer...

Answer 2

The base on the Replacement Stand-Off Brace for the Surco Universal Exterior RV Ladders #SPN-416 slides over the standoff tube and is held back with the lip formed by the end of the tube because the tube is widened at the other end. The base is then…

view full answer...

Answer 3

For a replacement ladder to install on the back of your motorhome I recommend the Stromberg Carlson RV Exterior Ladder, part #LA-401. This ladder has 7 steps and has pivoting mounting brackets at the top so you are sure to get a good fit. This ladder…

view full answer...

Answer 4

We have 2 ladder standoffs with square bases, the Replacement Stand-Off Brace for Surco Universal Exterior RV Ladders #SPN-416, and the Replacement Ladder Support Peg for Stromberg Carlson RV Exterior Ladder #8535 you referenced. They both have the…

view full answer...

Answer 5

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 6

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 7

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 8

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 9

The old version of the #HBA-CAM used 4 wires, but the product was updated awhile back and now uses only two wires as shown in the photo on the product description page. The white wire from the HBA-CAM would tap into the white ground wire and the blue…

view full answer...

Answer 10

To see all of the correct wheel and tire combos you'd need check out the link I attached. The option I would recommend is the part #TA43RR which is a Load Range C tire size ST175/80R13 mounted on a white spoke wheel with a bolt pattern of 5 on…

view full answer...

Answer 11

I have a solution for you, but we do not carry Glo-Brite lights, so replacing it with the same brand will not be something I can offer you. Instead, to replace your Glo-Brite 9852-88, I recommend using the Optronics LED Trailer Tail Light #STL72RB.…

view full answer...

Answer 12

The 40 amp fuse for your 2006 Chevrolet Silverado tow package is used for the 12 volt battery charge circuit. This fuse is located toward the front of the underhood fuse box closest to the front auxiliary positive post (see photo). There may be a…

view full answer...

How Does Stand Off Brace SPN416 Attach to RV Ladder and RV Wall

Product Page this Question was Asked From

Continue Researching