LED Light Strip Recommendation that Can Fit Groove in RV Awning

Question

Question:

I need 5/16 inch in the width, fits in a groove

asked by: Tom

0

Expert Reply:

The groove I believe you are referring to is designed to have a light track slid into it like the part # A30-0600 so that a thicker rope LED light can fit into it like the # A30-0625VP. None of the light strips we offer will fit into a channel that is only 5/16 inch in diameter.

expert reply by: Jameson C

0

Answer 1

We have LED light strips that fit the awning channel you have on your RV but the part #DG52683 that you referenced would not fit this application. Instead you'd want the part #A30-0625VP which is a 16 foot light strip that does fit the awning…

view full answer...

Answer 2

Thank you for the picture, I can see the pin is bent rendering your solera head shaft inoperable even though you tried bending it back. Unfortunately, the only fix would be to completely replace the head as this part isn't currently available…

view full answer...

Answer 3

If you happen to have a Lippert Solera awning, which is pretty common, you'd want the LED Fabric Light Kit #LC674283. It measures 21 feet long but can be cut down to size. The kit includes a switch and plate as well.

view full answer...

Answer 4

The two magnet kits work opposite of each other so since you tried the #LC301694 and it operated your steps in reverse the part #LC369299 that you have now is the correct kit for your Kwikee 28 step kit.

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 9

When it comes to choosing between the Blue Ox Patriot #BLU37TR and the Brake Buddy Select 3 #HM39524, these systems are extremely similar in their setup and functionality. Both of these systems provide proportional braking in a compact and easy to…

view full answer...

Answer 10

You are correct that this refrigerator does not have an ON/OFF switch or function. The best you can do is "Standby" that draws an unknown amount of power. One option is to pull the 12-Volt fuse at the RV power center. A much better option…

view full answer...

Answer 11

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 12

Both the Roadmaster and Blue Ox tow bars are great options. But if it was my decision to make I would go with the Blue Ox Avail part #BX7420 as we have found that the Blue Ox tow bars are a little easier to connect and disconnect from. Also this tow…

view full answer...

LED Light Strip Recommendation that Can Fit Groove in RV Awning

Continue Researching