Can Ultra Fab Steel Roller be Used on 2 inch Hitch of 2019 Subaru Outback

Question

Question:

Will this work for a 2019 Subaru Outback? We have a steep driveway.

asked by: Linda

0

Expert Reply:

Yes, the Ultra-Fab Steel Roller # UF48-979020 that you referenced will fit the 2 inch hitch you have installed on your 2019 Subaru Outback. It will help with the dragging you are experiencing with the steep driveway as well.

expert reply by: Jameson C

0

Answer 1

This is a fairly common issue with the Town and Country. However our suspension kits like #TDVRRT are not designed to work as a lift kit for the rear end of your truck. They are designed to help reduce the strain on your rear axle when you are…

view full answer...

Answer 2

I do have an option for you but the Curt Trailer Hitch Receiver part #13390 on your 2015 Subaru Legacy already has the highest ground clearance (10-1/4") of any other trailer hitch receiver we have confirmed to fit your vehicle. This measurement…

view full answer...

Answer 3

I do have an option for you but due to the way the vehicle is setup, all of the trailer hitches they make for it will hang down rather low. The other option I have for you to prevent it from scraping the pavement would be to use a skid wheel like the…

view full answer...

Answer 4

I have a solution for you, but the Timbren #TTORSEN04 are not going to significantly lift the rear end of your vehicle and really aren't intended for this purpose. These are designed for when you're towing a camper that has a heavier tongue…

view full answer...

Answer 5

I don't have a way to verify fit of the AMPLock Trailer Hitch Receiver Lock part #AMP37FR on a 2020 Toyota Tacoma but we can offer you this same pin with a longer usable span, the AMPLock Trailer Hitch Receiver Lock for 2-1/2" or 3"…

view full answer...

Answer 6

We do not have the CAD drawings or blueprints for the Ultra-Fab Steel Roller, part #UF48-979020, but I have attached a photo of the roller with dimensions shown. The mounting bracket measures 1-1/4 inches from the center of the hitch pin hole to the…

view full answer...

Answer 7

That's a really good question, and the weight ratings for the Equa-Flex Cushioned Equalizers are per axle as opposed to the weight of the trailer; so you will want to choose the kit that meets whatever your axles are rated for: - 3,000 lbs to…

view full answer...

Answer 8

We have just what you need to replace your landing gear motor M9000PK with the #LC196308 and you'd be set! This is a confirmed fit for what you have and is a faster motor too so your jacks will raise and lower quicker.

view full answer...

Answer 9

Really you're going to need to measure the distance where the leveling system is going to be installed. If that distance is more than 20', then you're going to want the 6 point Lippert Ground Control 3.0 Electric 5th Wheel RV Leveling…

view full answer...

Answer 10

To determine the correct height and location to install the Ultra-Fab Steel Jumbo Roller for Trailers and RVs #UF48-979023 you'll want to take a piece of wood or something long enough and straight to wedge up next to your tire and then hold at an…

view full answer...

Answer 11

If your Kwikee Steps #LC3711363 all of a sudden aren't operating correctly on a nearly brand new motorhome then my first recommendation would be to check the wiring for any damage or loose connections and then test the ground and the 12v power…

view full answer...

Can Ultra Fab Steel Roller be Used on 2 inch Hitch of 2019 Subaru Outback

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching