Picking Out Replacement Landing Gear Box for Venture Landing Gear

Question

Question:

Are the three landing gear, gear boxes that you offer interchangeable? LG179015, LC276602, RVLG-RDBOX. I have a2003 Keystone Sprinter 292fwrls with a Venture MFG part # vmc940rb-010209 Gear box with a Lippert electric drive motor part #m9000pk. I believe the electric motor is good as it tries to extend the LG but the gear box just slips and pops.

asked by: Herman L

0

Expert Reply:

The first two you mentioned are interchangeable and would work well with your Venture landing gear part numbers # LG-179015 and # LC276602, but the third part number # RVLG-RDBOX is for a different brand of Ram jacks and would not work for you. It does sound like your gear box is at fault though so it would be time to replace it. I'd go with whichever of the first two you mentioned that has best price as they are essentially the same.

expert reply by: Jameson C

0

Answer 1

That is a Venture/ADTH motor and gear box, and what you use to replace it is a motor and gear box from Stromberg Carlson, which are the following part numbers: - Replacement Motor #LG-142178 - Replacement Aluminum Gearbox #LG-179015

view full answer...

Answer 2

If you can send me a picture of your landing gear box I'll most likely be able to identify it. The most popular gear box we have would be the part #LG-179015 which fits most brands out there like Atwood, Lippert, and Venture.

view full answer...

Answer 3

We have the same part number basically twice through two different vendors here that are the exact replacement motor you are looking for. The Lippert part #LC142178 and the Stromberg part #LG-142178. They are the exact same motors and if I were you I…

view full answer...

Answer 4

We have just what you need to replace your landing gear motor M9000PK with the #LC196308 and you'd be set! This is a confirmed fit for what you have and is a faster motor too so your jacks will raise and lower quicker.

view full answer...

Answer 5

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 6

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 7

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 8

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 9

Since Demco uses 3,500 drum brake assemblies part #DMSB24429M and #DMSB24428M what you'd need is similar 3,500 electric brake assemblies like the etrailer part #AKEBRK-35L-SA for the left hand side and #AKEBRK-35R-SA for the right hand side. To…

view full answer...

Answer 10

The old version of the #HBA-CAM used 4 wires, but the product was updated awhile back and now uses only two wires as shown in the photo on the product description page. The white wire from the HBA-CAM would tap into the white ground wire and the blue…

view full answer...

Answer 11

You will need the Red LED Trailer Clearance or Side Marker Light #328-K-52 or Amber LED Trailer Clearance or Side Marker Light #328-K-51 for your 2018 Forest River Sunseeker motorhome. These lenses have the same Top Command SAE-AP2-16 markings on the…

view full answer...

Answer 12

What you're going to need is two of the transfer switches in that case. I have attached a diagram from Furrion that shows you how you're going to need to hook the two transfer switches #F30ATS up: -one to the other, then one branching off to…

view full answer...

Picking Out Replacement Landing Gear Box for Venture Landing Gear

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching