How to Attach E-Tracks to Cargo Trailer Walls

Question

Question:

What is the best tools to use for installing etrack on the side walls of cargo trailer and how difficult is this to do?

asked by: Barry

0

Expert Reply:

When attaching e-tracks like the part # E19148 typically people run the bolts through the track, then through the wall or floor they are attaching the track to, through the backing plate like part # e96RR, and then finally the nuts get threaded onto the bolts. For a cargo trailer wall application though you might just use appropriately sized wood screws through all of the mounting holes to attach to the support beams of the trailer walls.

expert reply by: Jameson C

0

Answer 1

As you mentioned, the integrated brake controllers on your Silverado 3500 trucks will typically not work with electric over hydraulic trailer brakes. The Chevy/GMC factory controllers are simply not compatible with electric over hydraulic brakes and…

view full answer...

Answer 2

I didn't receive your photos, but the manner in which you attach the e-track to your trailer deck will completely depend on what the deck is constructed of and where exactly on the deck you'll be placing the e-track. Without knowing any…

view full answer...

Answer 3

If you're looking for wall storage, then the CargoSmart X-Track Trailer Shelf Bundle - Matte Black - Steel - 667 lbs - 5' Long #3481788-T would be the correct solution and it will give you the ability to hang some hooks; if you can locate the…

view full answer...

Answer 4

When attaching e-tracks like the part #E19148 typically people run the bolts through the track, then through the wall or floor they are attaching the track to, through the backing plate like part #e96RR, and then finally the nuts get threaded onto…

view full answer...

Answer 5

I attached the picture I believe you were referencing for securing a Smart car too a Aluma trailer using E-track. The straps used in the picture are the Erickson Adjustable Wheel Net with E-Track Fittings #77314 which basically just snap into place…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 8

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 9

You're correct. The repalcement for your existing B12EA-22 brake would be #AKEBRK-7R-SA for the right side and #AKEBRK-7L-SA for the left.

view full answer...

Answer 10

Load range B trailer tires are going to have a lower capacity than C load range tires. Basically that, psi rating, and the ply rating are the only differences. A higher load range tire would last a little longer than lower load ranges of the same…

view full answer...

Answer 11

To find the load capacity for your axle you should look on the trailer VIN plate or sticker that lists the VIN number. The weight rating of the axle should be listed on that same plate or sticker. Also, the axle could have a tag or plate on it that…

view full answer...

Answer 12

For a single axle trailer, you want the shackle strap to be able to move so that you have the spring deflection needed for your suspension. Angled like the photo or even almost vertical is fine you just don't want the shackle strap to bind and…

view full answer...