Recommended Timbren System for a 2015 Toyota Tacoma 4x4 with 4 Leaf Spring Pack

Question

Question:

I have a 2015 4x4 Tacoma DC OR short bed. I have a 4 leaf pack with AAL. Lift was only about 1-1/4” after AAL. Ride actually improved!. I have tried Sumosprings and hate them as they are always in contact with frame making for a harsh ride when empty. Distance from springs to frame is approx 6” I tow a camper with tongue weight of 200lbs. Looking at future to tow one @ 320lbs. Also adding 200lbs topper. I have had air bags in past and we’re a pain to maintain. I’ve had Timbrens ones ending with L on similar truck 2005 with 4 leaf pack TSB and they were perfect for me. Tongue weight was higher and had crossbox full of tools. Truck loaded stayed level. Can’t decide on which Timbrens to get. What are your thoughts on this?

asked by: Bill

0

Expert Reply:

If you really liked the performance of the Timbren system then I recommend using the part # TTORTUN4 which is the fit for the 4 leaf spring pack on your 2015 Toyota Tacoma. I went out and found that the kit measures about 5-3/8" tall so since you have 6" between your leaf springs and frame this puts you right in the 1/2" to 1-1/2" gap that Timbren recommends.

This Timbren kit is rated for up to 6,000 lbs but please keep in mind that this does not increase the weight rating of your Tacoma, it only helps support up to that much weight.

expert reply by: Jon G

0

Answer 1

I went out and pulled both the Timbren kit part #TTORTUN4 and #TTORTUN4L from our warehouse to measure them for you and found that they both sit exactly 3-3/4 inches tall.

view full answer...

Answer 2

For your 2018 Toyota Tundra the suspension enhancement I recommend is the Timbren kit part #TABSOSR because this kit installs easily, gives you the suspension support you need to greatly reduce the sag, and because it doesn't require monitoring…

view full answer...

Answer 3

I have a great SumoSprings solution for you. Unfortunately, the blue SumoSprings Solo Custom Helper Springs - Rear Axle #SSR-610-40 will not fit your 2021 Toyota Tacoma Trd 4x4. With that being said, for higher capacity springs on your truck to give…

view full answer...

Answer 4

The correct Timbren Rear Suspension Enhancement System for a 2019 Toyota Tacoma is part #TTORTUN4L if you have three leaves in the rear leaf spring pack or part #TTORTUN4 if you have four leaves in the rear leaf spring pack. Therefore, the main…

view full answer...

Answer 5

The Timbren Springs for your 2012 Toyota Tundra Crew Max 4x4 like #TABSOSR all install to the spring stack at the rear and not to the frame. The front mounted springs #TABSTOF do however mount to the frame. All of the rear suspension enhancement…

view full answer...

Answer 6

Since weight distribution shouldn't be used on a trailer with a swing away tongue what you would want is suspension enhancement for your 2015 Toyota Tundra that will remove the sag you are experiencing. For that the Timbren Kit part #TTORTUN4 is…

view full answer...

Answer 7

The Timbren Front Suspension Enhancement System, part #TTOFTUN4, mounts where your factory bump stops are mounted. To install part #TTOFTUN4, you will have to remove the factory bump stops and replace with the Timbren System. I attached a picture…

view full answer...

Answer 8

I have a really great solution to give you additional suspension support and will also improve the ride quality and handling the RAS systems like the part #RAS34FR that fits your 2016 Toyota Tundra. I wouldn't recommend front suspension…

view full answer...

Answer 9

To get the mounting plate for the Timbren of part #TTORTUN4L onto the suspension of your 2012 Toyota Tacoma will require the temporary loosening of the U-bolts. This will allow you to slip the U-bolts over the plate so that it can be secured after…

view full answer...

Answer 10

For sag from towing a trailer the best recommendation I can make is actually a weight distribution system. Suspension enhancement will help level your truck while towing. But the advantage to a weight distribution system is that it levels the vehicle…

view full answer...

Answer 11

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 12

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...