Does Replacement Light Switch # EJ-3520-LSW Come with Bezel

Question

Question:

Good Afternoon, I was wondering if this replacement switch has this... bezel, clip, retaining plate? Im not sure what to call it. My Ram tongue jack was delivered with it broken and would love to fix it. Thanks for your time...

asked by: Mark P

1

Helpful Expert Reply:

The Replacement Light Switch # EJ-3520-LSW that you referenced does include the bezel piece you sent in a picture of that's broken on your jack. Whoever you bought this from should cover the replacement since it showed up like this. I checked our order notes though and didn't see you in our system.

expert reply by: Jameson C

1

click to enlarge

Answer 1

To replace a switch on your RAM 3,500 lb jack you just need the Replacement Power Switch #EJ-3520-PSW, but this also could be a bad internal screw. To determine if it's the switch or the screw you just need to remove the plug on top of the jack…

view full answer...

Answer 2

Your RAM 3550 Jack will use both the Replacement Power Switch for RAM Electric Trailer Jack with Footplate #EJ-3520-PSW and the Replacement Light Switch for Electric Trailer Jack with Footplate #EJ-3520-LSW.

view full answer...

Answer 3

There isn't a wrong way to install the Replacement Power Switch #EJ-3520-PSW for your Electric Jack #EJ-3520-BBX, just a wrong way to wire it. So long as you wire it like you see in the accompanying photo you won't have any issues.

view full answer...

Answer 4

I have attached a photo you can use to connect the Replacement Power Switch #EJ-3520-PSW to your 3,500 lb RAM jack. We don't have a direct wiring diagram but if you notice even though the wires are the same colors they look pretty different so…

view full answer...

Answer 5

What you need to replace the light in your Ram Jack a-frame powered jack is the part #EJ-3520-LT.

view full answer...

Answer 6

Your RAM jack model ej-3550-bbx will use the Replacement Light Switch #EJ-3520-LSW and Replacement Power Switch #EJ-3520-PSW.

view full answer...

Answer 7

We don't have an install video but basically what you have to do is remove the outer shell of the jack and then squeeze the top and bottom of the switch so that it can push through the mounting hole and then pop the new one in place.

view full answer...

Answer 8

I am not 100 percent sure what size you need, but a small option for a single-pole rocker switch is the Pollak Universal-Design Rocker Switch #PK34308. This switch is less than an inch wide (15/16") and just under 1-3/4" tall…

view full answer...

Answer 9

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 10

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 11

Since Demco uses 3,500 drum brake assemblies part #DMSB24429M and #DMSB24428M what you'd need is similar 3,500 electric brake assemblies like the etrailer part #AKEBRK-35L-SA for the left hand side and #AKEBRK-35R-SA for the right hand side. To…

view full answer...

Answer 12

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Does Replacement Light Switch # EJ-3520-LSW Come with Bezel

Product Page this Question was Asked From

Continue Researching