What Are Dimensions of Stromberg Carlson Fifth Wheel Tailgate # VGD-94-101

Question

Question:

I have a 63.2 inch x 17 inch tailgate. Will it fit a 1999 Dodge pickup

asked by: Judy W

0

Expert Reply:

Looks like the dimensions you mentioned are too small to fit a 1999 Dodge Ram. The Stromberg Carlson Fifth Wheel Tailgate # VGD-94-101 you mentioned does fit your truck but it's much taller. It measures 64-7/16 inch by 21-5/8 inch.

expert reply by: Jameson C

0

click to enlarge

Answer 1

The Louvered Tailgate Insert #VI-4000 for the Stromberg Carlson 4000 Series 5th Wheel Louvered Tailgate with Lock for Dodge Trucks #VGD-02-4000 is about 9-3/4" tall so if you measure down about 10" from the top of your bed rails on…

view full answer...

Answer 2

Seal 171255UC has an inner diameter of 1.719 inches and outer diameter of 2.565 inches. A seal that has those dimensions would actually be #58846. I've added a link to a video review of this seal for you to take a look at.

view full answer...

Answer 3

I do have an option for you, but we do not carry the Dexter 072-027-00 you mentioned. However we do have the etrailer Double-Eye Spring for 7,000-lb Trailer Axles - 24-7/8" Long #e64SR which will be 3/8" shorter but that is still…

view full answer...

Answer 4

The correct replacement for a Demco Master Cylinder 05680-C is the Replacement Master Cylinder part #5650. I spoke with Demco to confirm this for you.

view full answer...

Answer 5

The correct replacement master cylinder kit we have for your Demco setup is the part #DM5918 which comes with the lock out replacement.

view full answer...

Answer 6

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to…

view full answer...

Answer 7

Hi Jeremy; that's a good question and you'll actually need to go ahead and re-do the set up of your weight distribution system after adding the Timbren Rear Suspension Enhancement System #TDR1500DS to your 2019 Ram 1500. So it wouldn't…

view full answer...

Answer 8

Yes, you are correct. In order to correctly take this measurement you will need to measure from the center of the spindle to the center of the main axle tube. I have included a picture for reference.

view full answer...

Answer 9

According to my contact at Fantastic Vent the correct replacement lift motor to use in your vent is part #FVK6010-81, not item FVK-6050-80. The replacement motor does operate at a higher 17-RPM speed. Since your fan is of a lower rpm and manufactured…

view full answer...

Answer 10

The #99 trailer spindle is typically found on 9,000 lb and 10,000 lb axles. This is not a spindle that we carry at this time, but I did find some of the measurements. I have attached a diagram showing the dimensions of a #99 spindle for you to check…

view full answer...

Answer 11

In order to charge your batteries wired in parallel with the NoCo Genius #329-GENIUS5 you'll want to connect the positive charge line to the positive terminal of the first battery and the negative line to the negative terminal of the opposite…

view full answer...

Answer 12

The DeeMaxx item #DE86VR won't because of the spacing on the mounting bracket but I have a caliper that will. To replace your Tie Down Engineering 46304 caliper you will need the Kodiak Disc Brake Caliper item #KDBC225DAC.

view full answer...

What Are Dimensions of Stromberg Carlson Fifth Wheel Tailgate # VGD-94-101

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching