Correct Bearing Kit for a Lippert Trailer Idler Hub Part 122098

Question

Question:

Will this kit fit a Lippert 122098 hub? I have a Lippert 3500# axle with 122098 stamped on the back of the hub. Everything points to this kit but nothing positively confirms that. Aluma 8114BT utility trailer

asked by: Jason P

0

Expert Reply:

Yes, the Bearing Kit for #84 Spindles part # BK2-100 is correct for your Lippert Trailer Idler Hub part 122098. I confirmed this with Lippert for you as well.

expert reply by: Conner L

0

Answer 1

E-Track such as the Erickson Horizontal E-Track #E19148 can be used in any way that allows you to mount your pair of motorcycles. As you can see in some of the photos I've added, there is not a set way to add the track. You will need to take…

view full answer...

Answer 2

From the numbers you provided it sounds like you need replacement grease seals. In my research, the grease seals I found with the GS-1719DL number have a 1.72 inside diameter and 2.565 outside diameter. The replacement double lip grease seals you…

view full answer...

Answer 3

I do have an option for you but I cannot give you exact bearing numbers for your trailer unless provided with spindle measurements or the trailer's VIN (if the manufacturer is still in business). I can however tell you that the two most common…

view full answer...

Answer 4

The bearing kit part #BK2-100 is a kit designed specifically for 3,500 lb axles like what your trailer has. This will work well for your trailer and comes with all of the needed bearings, races and seal. I attached an install video for this kit for…

view full answer...

Answer 5

I can help you figure out what bearings and grease seal you need for your EZ Loader trailer, though since there isn't a single kit we offer designed for these trailers there are a couple of steps you'll need to take first. You will need to…

view full answer...

Answer 6

There are really two reasons to replace a grease seal, if they are damaged or worn and leaking grease then that is an obvious factor. If you are replacing bearings it is usually best to replace the grease seals as well because although they may still…

view full answer...

Answer 7

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 8

Yes, the Timken Bearing Kit #TMK52VR will fit your 3,500 lb axle as it fits an standard #84 spindle. The only time this kit won't fit with a 3,500 lb axle is if the trailer/axle is made before the 2000's since that's about the time that…

view full answer...

Answer 9

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Answer 10

The Dexter bearing kit part number K71-717-00 that you referenced is the bearing kit for a number 84 spindle. Our part number for that bearing kit is #BK2-100.

view full answer...

Answer 11

Depending on how the trailer was made, there will be a few spots you can check to identify the axle. First, if the trailer was pre-made by a specific company, you may be able to find this information in either the paperwork or on a placard somewhere…

view full answer...

Answer 12

Hey Roy, The only U-bolt kit we currently only offer for 1-1/2" square axles is part #CE23102, which only has a 3-3/8" length so it likely wouldn't be the best option for you. Instead you'll want to order the 1-1/2" Square…

view full answer...

Correct Bearing Kit for a Lippert Trailer Idler Hub Part 122098

Product Page this Question was Asked From

Continue Researching