Dimensions of Nuts Included in Redline Replacement Axle U-Bolt 175668

Question

Question:

What is the nut size for these u-bolts?

asked by: Hjalmar E

0

Expert Reply:

Replacement U-Bolt # 175668 includes nuts with a 9/16-inch inside diameter and which require a 7/8-inch wrench. This part fits on 2-1/2-inch diameter round trailer axles.

expert reply by: Adam R

0

Answer 1

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 2

Thank you for providing the specs for the suspension components that you already have. Correct hanger spacing really depends on the components being used such as springs, hangers and equalizers. Most of the hanger spacing dimensions that we have are…

view full answer...

Answer 3

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 4

To find the load capacity for your axle you should look on the trailer VIN plate or sticker that lists the VIN number. The weight rating of the axle should be listed on that same plate or sticker. Also, the axle could have a tag or plate on it that…

view full answer...

Answer 5

For a single axle trailer, you want the shackle strap to be able to move so that you have the spring deflection needed for your suspension. Angled like the photo or even almost vertical is fine you just don't want the shackle strap to bind and…

view full answer...

Answer 6

To determine the size of the hub assembly you need to purchase you have to determine which bearings are in the old assembly. If the old assembly has L44649 inner bearings, you would use the hub you chose #8-258-5UC1. If the inner bearings are marked…

view full answer...

Answer 7

A BT8 spindle would have a diameter of .99 of an inch where the bearings would both install and would have a diameter of 1.24 where the great seal would ride. That would require a hub part #AKIHUB-440-2-1K for an idler hub. A BTR spindle would have…

view full answer...

Answer 8

Well shackle length is mainly based on the height difference between the front and rear hangers. The rear hanger normally doesn't hang as low as the front so that the shackle can offset the difference and add the ability to move. What is the…

view full answer...

Answer 9

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Answer 10

I have attached for you below some common torque values needed for a trailer suspension system but a lot of these will vary by bolt size and other factors. U-Bolts: Varies by Size - 1/2" bolts: 45 ft/lbs - 70 ft/lbs, 9/16" bolts: 65 ft/lbs…

view full answer...

Answer 11

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 12

The absolute best cushioned equalizer that fits the dimensions you mentioned having would be the MORryde ALLTREK 4000 part #MR89DR as this is only option to provide vertical and horizontal cushioning. This would make a big difference and you'd be…

view full answer...

Dimensions of Nuts Included in Redline Replacement Axle U-Bolt 175668

Product Page this Question was Asked From

Continue Researching