Should 12 or 18 Carpet be Used for 12 Long Bunk Boards

Question

Question:

My bunk boards are 12foot long. Will the 12foot foot long carpet have enough length to cover them or should I order the 18foot long carpet? Do I need the extra length to wrap around the ends of the board?

asked by: Robert C

0

Expert Reply:

Since your bunk boards are right at 12' long I recommend going with the 18' carpet # CE11349 instead of the 12' # CE11350 so that you will have some extra material to wrap around the ends like you mentioned.

expert reply by: Jon G

0

Answer 1

I can certainly understand not wanting to have to connect 2 five-foot carpeted bunk rails like #CE27820 to get the 10 foot bunks you need. We don't offer them in the 10' length because the shipping costs would be more expensive than the bunks…

view full answer...

Answer 2

The longest length of bunk carpet we offer in an 11 inch width would be 12 feet long which we offer in black as part #CE11330, charcoal as part #CE11372 or blue as part #CE11350

view full answer...

Answer 3

While the 7' Long CE Smith Carpeted Bunk Boards #CE27845 are the longest we carry for shipping, we do offer the carpeting separate that you can use on locally sourced lumber. We have a roll that is 12' long and 11" wide in a variety of…

view full answer...

Answer 4

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 5

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 6

If you are installing just the Firestone Ride-Rite kit, #F2400, and not also adding an on-board air compressor such as #F2158, then I would estimate that it should take about 2 hours to install the kit. That is for someone with some mechanical…

view full answer...

Answer 7

I would be happy to help you set up your 2022 Toyota Highlander to haul your new travel trailer. The wiring harness you currently have controls your trailer's lighting functions only. You do not need to rewire your Toyota you just need another…

view full answer...

Answer 8

If the trailer wheels scrubbed (dragged and scrapped the ground instead of rolling) when jack knifed then it could have thrown something out of alignment or damaged something. First, inspect the suspension. Look for any elongated holes where…

view full answer...

Answer 9

To tow your trailer that uses an RV style 7-way blade style connector with your semi that has a 7-pin connector, you need to construct an adapter that will also combine the brake signal into the right and left directional signal pins. This can be…

view full answer...

Answer 10

The Bargman 7-Way, RV-Style Connector #WG54006-043 referenced in your question uses the standard RV-style pin locations for its 7-Way connector. I have attached a diagram of these locations and their functions for you to check out. Wire colors will…

view full answer...

Answer 11

That spindle looks pretty well destroyed so best option is going to be to replace the axle. You are going to need to measure your current axles in a few places to get the correct one as we don't have access to what your numbers reference. You…

view full answer...

Answer 12

What you're going to need is two of the transfer switches in that case. I have attached a diagram from Furrion that shows you how you're going to need to hook the two transfer switches #F30ATS up: -one to the other, then one branching off to…

view full answer...

Should 12 or 18 Carpet be Used for 12 Long Bunk Boards

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching