How To Install the UWS Truck Bed Fender Well Toolboxes On a 2019 Ram 2500 Long Bed

Question

Question:

Does this require drilling holes in the truck bed or side wall to install? Im looking to buy driver and passenger side ones for my new truck 2019 Ram 2500 long-bed.

asked by: Robert E

0

Expert Reply:

Yes, the UWS Truck Bed Fender Well Toolboxes do require drilling for installation. The holes that will need to be drilled will be located wherever you choose. The recommended method is on the inside edge of the bed rail but you can also do so to the actual wheel well or to the bed floor. The process will vary for each installation and your choosing.

For your 2019 Ram 2500, the correct UWS Truck Bed Fender Well Toolbox is part # UWS01624 for the driver side and part # UWS01626 for the passenger side.

expert reply by: Conner L

0

Answer 1

Hey John, so the correct amount of spring bar tension will be based on the trailer's tongue weight and how it affects the suspension of your Nissan Frontier. Every WD system is a little different but what it comes down to typically is measuring…

view full answer...

Answer 2

Yes, the best option we can offer you to add fuel capacity is with the DeeZee Truck Bed Auxiliary Tank part #DZ91752X which should fit in the space you have between the cab and 5th wheel hitch no problem as it is only 9" deep. I don't have…

view full answer...

Answer 3

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 4

I got some information from Yakima and included a diagram of the EXO SwingBase #Y34VR, which is the base part for the EXO SwingBase 2 Tier #Y82VR. Though the measurement from the pin hole to the closest edge of the carrier is not included in said…

view full answer...

Answer 5

Yes, the Reese fifth wheel rail kit adapter part #RP30154 does work with the older Reese Select Plus 50008 slider base you mentioned.

view full answer...

Answer 6

The Reese #50008 is the part number corresponding to a round tube slider unit (the slider, but not the hitch) that is no longer being manufactured. According to my contact at Reese, their part #58161 is the correct replacement actuating handle for…

view full answer...

Answer 7

The measurements between the front and rear holes on the Adapter Rails for Curt 5th Wheel Hitch #C88KR are 20 1/2" center on center, and 29" center on center. These holes are spaced for the industry standard 5th wheel mounting holes.

view full answer...

Answer 8

Yes! The K-Source Snap & Zap Custom Towing Mirrors - Snap On #KS80730 has a clear lens to see the turn signal indicator as well as cutouts for the bottom sensor and under lights. I went ahead and attached a great review video that goes over all…

view full answer...

Answer 9

The 55" UWS Truck Bed Chest #UWS01030 has been confirmed by the manufacturer to fit a 2018 Ford F-150 with a 5-1/2 foot bed, though the other toolbox you mentioned is not a fit for this truck. To fasten this tool box to the bed of your '18…

view full answer...

Answer 10

The "Trailer Disconnected" error message on the dash with a factory brake controller is usually related to an issue with the blue brake output wire that runs from the brake controller to the 7-Way connector. The fact that the issue remains…

view full answer...

Answer 11

Yes, since the Camco Quick Hose Connect #CAM20135 uses all brass construction (lead-free and corrosion-free), the same as most faucets and hose fittings, this means it is perfectly safe for potable water. You are right that not all hoses are made of…

view full answer...

How To Install the UWS Truck Bed Fender Well Toolboxes On a 2019 Ram 2500 Long Bed

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching