Will UWS Truck Bed Toolbox Fit 2018 Ford F-150 with 5-1/2 Foot Bed

Question

Question:

Will both of these boxes fit between the wheel wells of a 5.5foot bed, 2018 F150? How is the box fastened to the truck?

asked by: Gary

1

Helpful Expert Reply:

The 55" UWS Truck Bed Chest # UWS01030 has been confirmed by the manufacturer to fit a 2018 Ford F-150 with a 5-1/2 foot bed, though the other toolbox you mentioned is not a fit for this truck.

To fasten this tool box to the bed of your '18 F-150 you are going to first need to drill though the box with an 11/32" drill bit and you'll then fasten it with washers and lock nuts.

expert reply by: Kyle S

1

click to enlarge

Answer 1

The correct Thule TracRac SR Sliding Truck Bed Ladder Rack for a 2019 Ford F-150 with 6-1/2' bed is part #TH43002XT-501. The TracRac SR mounts in the stake pockets on top of the bed rails. Therefore, you won't be able to use a…

view full answer...

Answer 2

We had a customer who was able to replace his Dexter 8-155 hubs with the #8-201-5UC3-EZ that you referenced so they should work well for you. You can verify that this hub will work for you by pulling your current hub and making sure they have inner…

view full answer...

Answer 3

For sag from towing a trailer the best recommendation I can make is actually a weight distribution system. Suspension enhancement will help level your truck while towing. But the advantage to a weight distribution system is that it levels the…

view full answer...

Answer 4

I looked up your Dexter 8-222 Hub and was able to find the inner and outer bearing numbers as well as the grease seal used. It looks like this particular hub was designed for mobile homes and these, for the most part, have more unique bearings and…

view full answer...

Answer 5

Yes the Replacement Brass Connector #T4750300 for Titan Disc Brake Actuators will fit a Tie Down 660e disc brake actuator.

view full answer...

Answer 6

To replace your AL-KO 568303 seal you will want the Oil Seal #91030. This seal has the same inner diameter of 2.750 inches and outer diameter of 3.779 inches. It is a confirmed fit for your #99 spindle that uses the AL-KO 568303 seal.

view full answer...

Answer 7

Yes, the Kodiak Disc Brake Caliper #KDBC250D will fit the caliper bracket that comes in the HydraStar Disc Brake Kits, like Kit #HSE7K-T1. We also have the Stainless Steel Kodiak Disc Brake Caliper #KDBC250S and Stainless Steel Ceramic Brake Pads…

view full answer...

Answer 8

It looks like the studs in your brake assembly are closer together (center to center) at the bottom. If the center to center bolt spacing matches the photo I've provided, then the #23-105-09 you'd looked at would be the correct…

view full answer...

Answer 9

The appropriate torque spec for any application will vary depending on the construction of the wheel as well as on the stud size. I suggest checking the wheels you're using to see if their manufacturer has a suggested torque rating. Steel…

view full answer...

Answer 10

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 11

Hey John, so the correct amount of spring bar tension will be based on the trailer's tongue weight and how it affects the suspension of your Nissan Frontier. Every WD system is a little different but what it comes down to typically is…

view full answer...

Answer 12

Yes, the best option we can offer you to add fuel capacity is with the DeeZee Truck Bed Auxiliary Tank part #DZ91752X which should fit in the space you have between the cab and 5th wheel hitch no problem as it is only 9" deep. I…

view full answer...

Will UWS Truck Bed Toolbox Fit 2018 Ford F-150 with 5-1/2 Foot Bed

Product Page this Question was Asked From

Continue Researching