Gear Box Replacement for Venture Model VMC 940RB-30

Question

Question:

Found a # VMC 940RB-30. Do you have a replacement gear box ? It’s on a 2008 Sunnybrook

asked by: Johnny Y

0

Expert Reply:

The correct replacement gear box you need for your Venture model that's labeled VMC 940RB-30 is the part # LC276602 which is a direct replacement.

expert reply by: Jameson C

0

Answer 1

Your trailer likely uses an Atwood or Lippert landing gear set up so you could replace the lead leg with a model from one of those manufacturers. Most landing gear major components on newer 5th wheel trailers are interchangeable if you get the…

view full answer...

Answer 2

To replace your existing Venture motor, the Lippert Components Venture 5th Wheel RV Landing Gear Motor #LC142178 is the correct replacement part for you. For an aluminum gear box, you are correct that you can use part #LG-179015. The #LC142178…

view full answer...

Answer 3

We have just what you need to replace your landing gear motor M9000PK with the #LC196308 and you'd be set! This is a confirmed fit for what you have and is a faster motor too so your jacks will raise and lower quicker.

view full answer...

Answer 4

For your Venture landing gear you can use #LC276602 or #LG-179015. Either one will work.

view full answer...

Answer 5

It depends on what 5th wheel landing gear you have. For example; the Lippert Landing Gear part #LC333966 is rated for 6,000 lbs. It can be used with a trailer that weighs more than 6,000 lbs because it is only supporting part of that load - the…

view full answer...

Answer 6

If the trailer wheels scrubbed (dragged and scrapped the ground instead of rolling) when jack knifed then it could have thrown something out of alignment or damaged something. First, inspect the suspension. Look for any elongated holes where…

view full answer...

Answer 7

While we may have an option for you, we do not have the exact specs on your Allis grease seal part number 5013 29772. However, with the 1.6" ID and 2.5" OD measurements you provides, that is very close to our #58846. This particular grease…

view full answer...

Answer 8

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 9

Seal 171255UC has an inner diameter of 1.719 inches and outer diameter of 2.565 inches. A seal that has those dimensions would actually be #58846. I've added a link to a video review of this seal for you to take a look at.

view full answer...

Answer 10

Based on my research, the Trailer Hub and Drum Assembly - 8,000-lb E-Z Lube Axles #AKHD-865-8-EZ-K will be a replacement for the 90865 Rockwell hub and drum. Both of these hub and drum assemblies are 12-1/4" diameter, have an 8,000 lb capacity,…

view full answer...

Answer 11

The part you referenced 127194TB is a double-lip seal with an inner diameter of 1.274-inches and an outer diameter of 1.983-inches. The available seal nearest to those dimensions that we offer is part #RG06-010, which is a double-lip seal sold as a…

view full answer...

Answer 12

A TCM double-lip grease seal number 127194 has an inner diameter of 1.274-inches and an outer diameter of 1.983-inches according to my research. The available grease seal nearest to those dimensions that we offer is part #RG06-010, which is a…

view full answer...

Gear Box Replacement for Venture Model VMC 940RB-30

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching