How Much Weight Can Landing Gear Hold
Question:
How much weight can a landing gear hold for the trailer is fully loaded will it hold it
asked by: David P
Expert Reply:
It depends on what 5th wheel landing gear you have. For example; the Lippert Landing Gear part # LC333966 is rated for 6,000 lbs. It can be used with a trailer that weighs more than 6,000 lbs because it is only supporting part of that load - the tires, wheels, and axles should be supporting the bulk of the weight. Keep in mind that the pin weight of a 5th wheel trailer is typically 20% of the loaded trailer weight.
As long as you are not going over the Gross Vehicle Weight Rating (GVWR) of your trailer and you have it loaded properly you will not need to be worried about over exceeding the weight capacity. The only time that might be a concern is if the OEM landing gear has been replaced with landing gear that is rated for a much lower weight capacity.
Product Page this Question was Asked From
Lippert Manual Landing Gear Set with Handle - Weld On - 37" Lift - 6,000 lbs
- Camper Jacks
- Fifth Wheel Camper
- Leveling Jacks
- Stabilizer Jacks
- Steel
- 5001 - 6000 lbs
- Landing Gear
- Sidewind Jack
- 37 Inch Lift
- Weld-On
- 2 Jacks
- Lippert
more information >
Featured Help Information
Instructions
Continue Researching
- Shop: RV Jack Pads
- Video: Interaction with E-Track
- Shop: Stromberg Carlson Base Pad Extreme for Campers and Trailers - 6,000 lbs - Qty 1
- Video: Stromberg Carlson RV and Trailer Jack Pads Review
- Video: Camco Clamp-N-Carry Chair Rack for Standard RV Ladders Review
- Shop: MORryde RV Cargo Sliding Tray - 48" x 36" - 1 Way Slide - 60 Percent Extension - 800 lbs
- Shop: Clamp-N-Carry Chair Rack for Standard RV Ladders - Nylon
- Shop: Easy Grease Trailer Hub and Drum Assembly for 6K Axles - 12" - 6 on 5-1/2 - Galvanized
- Shop: Timbren Axle-Less Trailer Suspension - Standard Duty - 4" Lift - 5 Bolt Flange - 5,200 lbs
- Search Results: timbren
- Search Results: timbren trailer axles
- Q&A: How to Measure to Pick Out Replacement Landing Gear for a Trailer
- Shop: Curt Wheel Chock w/ Handle and Mounting Bracket - Solid Rubber - Qty 1
- Q&A: Lippert 6-Point Level-Up System Foot Pad Torque Requirement
- Shop: Jeep Spare Tire Carriers
- Search Results: horizontal e track
- Search Results: e~track cargo organizers
- Search Results: jack pad
- Search Results: wheel chock
- Video: Stromberg Carlson RV Lawn Chair Rack Review
- Video: Camco RV Cargo - Lawn Chair Racks - CAM51430 Review
- Video: Lippert Offset Cable Spare Tire Winch Review
- Video: Dutton-Lainson Offset Trailer Spare Tire Carrier Review and Installation
- Search Results: cargo slides
- Shop: Offset Trailer Spare Tire Mount by Dutton-Lainson
- Shop: Fifth Wheel Hitch
- Q&A: Recommended Replacement for Duo Therm 6300035.321 RV AC Unit
- Q&A: Do Landing Gear Drop Legs have to be Pinned in at the Same Height or Can they be Off
- Q&A: Replacement Trailer Landing Gear Slave Leg for Atwood Landing Gear
- Q&A: Are Replacement Parts for Atwood Landing Gear Available or Will Another Brand Fit
Cable H.
6/16/2020
What size landing gear do i need to lift a trailer with 2000 pounds of pin weight?