Roof Vent Replacement Recommendation for 2014 Rockwood 1640LTD

Question

Question:

Hello! I am in need of a replacement roof vent cover for my 2014 Rockwood 1640ltd pop up camper. I noticed the one on there has 5 hinges, and not 4 like the one in your guide. Do you know what model I should use to replace it? Are they all a standard size? I am attaching a photo of what is currently on the camper. Thank you!

asked by: David

0

Expert Reply:

I really appreciate you getting me a picture of the roof vent lid you have on your trailer but since we don't have anything that matches what you sent in your best option will be to replace the entire roof vent like with the Ventline Ventadome part # V2092SP-28. This will fit the same roof opening dimensions you have currently and will give you an all new setup that will work great.

expert reply by: Jameson C

0

click to enlarge

Answer 1

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 2

For the front legs of a Lippert Ground Control 3.0 kit the replacement front jack leg solution you'd need is the part #LC362485. This will allow you to reuse your current motor and bracket. There isn't a gear replacement kit for the…

view full answer...

Answer 3

Hey David, we've used the LaSalle Bristol RV Roof Vent install kit part #344270KITW to install several MaxxFan RV roof vents and it's worked well so it would also work well for you. This comes with everything needed so it would be a…

view full answer...

Answer 4

Hi Christopher, There unfortunately isn't a guide to tell us the exact part numbers for the vents, skylights, etc. on your Passport. We offer a variety of plumbing vents and 12v fan vents but we unfortunately do not offer skylights. If you want…

view full answer...

Answer 5

In order to determine the correct roof vent, measure where the vent opens. The standard trailer roof vent opening is roughly 14-1/4" x 14-1/4" and have roof vents that measure 14" x 14". To pick the correct cover, you will also…

view full answer...

Answer 6

Yes, for 5,200 standard trailer axles we have the hub part #8-219-4UC3-EZ which is a fit for 5,200 lb axles and has the bolt pattern of 8 on 6-1/2 inches like you said you need.

view full answer...

Answer 7

Those are Warner trailer brakes. This style is not made anymore and replacement parts are hard to find. We have some parts for the larger Warner assemblies but NOT the 12 x 2 inch ones. Most people end up replacing them. You will have to have…

view full answer...

Answer 8

You can attach D-Ring Tie Downs most anywhere on a trailer. You need to select the location based upon what you need to tie-down. When possible, it would be best to drill through metal to install the rings. You can mount them to the wood planks, but…

view full answer...

Answer 9

The Replacement 18'1" Fabric for 19' RV Awning item #LCV000334424 you were looking at is made for Solera, Dometic A&E, or Carefree RV awnings. It is for a 19' awning assembly and measures 18'1" x 8'. In order to…

view full answer...

Answer 10

Put the pin back in and wind it 12-16 times rolling it towards the camper to put the correct tension in the slide topper #LCV000163285 before installing it. This will give you the correct amount of tension for extending and retracting the awning.

view full answer...

Roof Vent Replacement Recommendation for 2014 Rockwood 1640LTD

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching