Can Manual Override Brake Voltage Backfeed of Brake Controller be Stopped
Question:
I am installing a Redarc Tow-Pro Elite brake controller that I purchased from you ti install in my Sprinter. The directions describe the requirements for the vehicle brake light connection and that it must accept battery voltage input when the brake controller manual over-ride is operated and illuminate at least the trailer brake lights. In this Mercedes document they say the brake signal wire is OUTPUT ONLY. You sell the wiring harness to connect them. Would all brake controllers have the same requirements and is this OK to connect without damaging the vehicle? Thanks for the help.
asked by: Eric B
Expert Reply:
Brake Controllers like the Tow Pro Elite # RED44FR have as safety function built into them that activates the tow vehicle's brake lights if the manual override lever is applied so that other motorists know you are slowing down. Not all vehicles like this voltage and some will show an error code on the dash.
The solution for this is to install a one-way diode like the # RM-690 which only allows voltage to travel in one direction which would solve your problem. This installed on the red wire of the brake controller would only allow voltage to travel from the brake pedal to the controller.
Products Referenced in This Question
Redarc Tow-Pro Elite Brake Controller - Dash Knob - 2 Braking Modes - 1 to 3 Axles - Proportional
- Trailer Brake Controller
- Proportional Controller
- Electric
- Electric over Hydraulic
- Automatic Leveling
- Dash-Mounted Knob
- Hidden
- Up to 3 Axles
- Indicator Lights
- Redarc
more information >
Roadmaster Single Park Light Diode
- Accessories and Parts
- Tow Bar Wiring
- Diodes
- Roadmaster
more information >
Product Page this Question was Asked From
Tekonsha Primus IQ Trailer Brake Controller - 1 to 3 Axles - Proportional
- Trailer Brake Controller
- Proportional Controller
- Electric
- Automatic Leveling
- Under-Dash Box
- Dash Mount
- Up to 3 Axles
- LED Display
- Up to 90 Degrees
- Tekonsha
more information >
Featured Help Information
Instructions
Miscellaneous Media
Continue Researching
- Shop: Brake Controller
- Video: Review of Redarc Trailer Brake Controller - Encapsulated Power Diode - RED34FR
- Shop: Redarc Encapsulated Power Diode for Tow-Pro Brake Controllers
- Video: Redarc Tow-Pro Elite Trailer Brake Controller Installation - 2021 Chevrolet Colorado
- Search Results: trailer brake controller
- Shop: Redarc Tow-Pro Liberty Brake Controller w/ Universal Wiring Harness - Dash Knob - Proportional
- Q&A: Is The Redarc Encapsulated Power Diode # RED34FR Needed On a 2016 Toyota Highlander W/ Redarc Elite?
- Search Results: brake controller install
- Shop: Master Lock Hitch Receiver and Coupler Latch Lock Set - Swivel Design - 2" Hitches
- Shop: Redarc Tow-Pro Liberty Brake Controller - Dash Knob - 1 to 2 Axles - Proportional
- Q&A: Where to Find Stoplight Circuit for Install of Redarc EPDK Diode on 2020 Subaru Outback
- Q&A: Solution to Allow Trailer Running Light Circuit to Function on 2019 GMC Sierra 1500
- Shop: Trailer Wiring
- Search Results: lock
- Search Results: tie down
- Q&A: Troubleshooting Redarc Tow-Pro Liberty Calibration
- Q&A: What is the Red Wire Function on an Electric Trailer Brake Controller
- Search Results: brake light diode
- Q&A: Preventing Pre-Collision Warning of 2018 Toyota Highlander After Brake Controller Install
- Q&A: Parts Needed To Install The Redarc Tow-Pro Liberty And A 2022 Honda Ridgeline
- Shop: 7-Way Trailer Adapter for Towing Trailers with LED Lights
- Shop: Roadmaster Hy-Power Diodes (Qty 2)
- Shop: Vehicle to Vehicle Tail Light Converter
- Video: Roadmaster Tow Bar Wiring RM-792 Review
- Search Results: curt universal
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Article: Wiring Trailer Lights with a 7-Way Plug (It's Easier Than You Think)
- Article: Brake Controller Installation: Starting from Scratch
- Video: Best 2020 Toyota Highlander Trailer Wiring Options
- Video: Curt Wiring - Wiring Adapters - C57102 Review