Picking Out Grease Seal for 2000 Coleman Taos Pop Up

Question

Question:

Hi. Can’t find the correct grease seal for my Coleman Taos popup camper. Could you help me out with this please? Thank you.

asked by: Beth

0

Expert Reply:

To pick out a replacement grease seal you will need to measure the diameter of the spindle where the grease seal rides with a digital or dial caliper and then need to measure the hub bore where the current seal rides. With those two dimensions we can pick out the correct seal that you would need.

I attached a link to a page that has all of the grease seals we carry. You will need to select your inner and outer diameter from the filters on the page and the correct seals will be listed.

expert reply by: Jameson C

0

click to enlarge

Answer 1

To discover and repair the problem, you'll need to closely examine the taillight wiring system on your trailer. Begin at the connector, and closely examine it for damage or excessive green or white corrosion. Clean/repair or replace as…

view full answer...

Answer 2

We can help you find the seal you need, but the part number you mentioned does not match anything we offer. Can you get me the inner and outer diameters of the seal? With that I can see what we have that matches.

view full answer...

Answer 3

Grease seal set #RG06-050 is what you will need. These are double lip seals, just like what you have (the spring indicates that) and the dimensions are all the same including the 1/2 inch width.

view full answer...

Answer 4

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 5

The wheels are hub-centric. The wheel bolts instead of lug nuts is the only clue needed. A hub-centric wheel centers on the hub using the pilot hole and hub so it would be a snug fit. You could still use a lug-centric wheel as long as the pilot hole…

view full answer...

Answer 6

The wheel/tire combos we offer are not balanced at the factory. When the tire is mounted to the wheel, the high or heavy spot on the wheel is matched to the low or light spot on the tire, which leaves the wheel and tire somewhat balanced. You can…

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

To determine the size of the hub assembly you need to purchase you have to determine which bearings are in the old assembly. If the old assembly has L44649 inner bearings, you would use the hub you chose #8-258-5UC1. If the inner bearings are marked…

view full answer...

Answer 9

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 10

A BT8 spindle would have a diameter of .99 of an inch where the bearings would both install and would have a diameter of 1.24 where the great seal would ride. That would require a hub part #AKIHUB-440-2-1K for an idler hub. A BTR spindle would have…

view full answer...

Answer 11

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Answer 12

To find the load capacity for your axle you should look on the trailer VIN plate or sticker that lists the VIN number. The weight rating of the axle should be listed on that same plate or sticker. Also, the axle could have a tag or plate on it that…

view full answer...