Replacement for a Fulton F2 1600 Pound Trailer Jack That Has Mounting Hardware

Question

Question:

I need to replace a fulton 1600 with the bolt on bracket that turns sideways, the screw is rusted, I would just buy that but cant seem to. what is the replacement for this, a bit heavier would be better.

asked by: Warwick

0

Expert Reply:

I recommend the Fulton F2 with the wide wheel. This is a 1600-pound capacity jack that includes the mounting hardware. The model number is # F1413040134.

expert reply by: Michael H

0

Answer 1

If you are speaking of the gearbox cover or cap on the top of the jack that is secured by four screws, the replacement is part #F500135. If you are speaking of the black plastic piece below that cover that wraps around the jack with the hole for…

view full answer...

Answer 2

That's not a part we can get as Fulton does not offer it as a replacement part. Only solution we have would be a new jack like the F2 part #F1413140334.

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 7

To determine the size of the hub assembly you need to purchase you have to determine which bearings are in the old assembly. If the old assembly has L44649 inner bearings, you would use the hub you chose #8-258-5UC1. If the inner bearings are marked…

view full answer...

Answer 8

A BT8 spindle would have a diameter of .99 of an inch where the bearings would both install and would have a diameter of 1.24 where the great seal would ride. That would require a hub part #AKIHUB-440-2-1K for an idler hub. A BTR spindle would have…

view full answer...

Answer 9

To find the load capacity for your axle you should look on the trailer VIN plate or sticker that lists the VIN number. The weight rating of the axle should be listed on that same plate or sticker. Also, the axle could have a tag or plate on it that…

view full answer...

Answer 10

In order to verify the spindle dimensions so that you can pick out the correct hub/drum you have to get exact dimensions. For that you need to use a digital caliper like part #PTW80157. For how old your trailer is this is especially important as the…

view full answer...

Answer 11

Depending on how the trailer was made, there will be a few spots you can check to identify the axle. First, if the trailer was pre-made by a specific company, you may be able to find this information in either the paperwork or on a placard somewhere…

view full answer...

Answer 12

The BTR and BT8 denotations refer to the spindle, not the trailer hub. The difference between a BTR and BT8 spindle is that the BTR spindle uses a 1.063" diameter L44649 bearing and the BT8 spindle uses a 0.99" diameter L44643 bearing. In…

view full answer...

Replacement for a Fulton F2 1600 Pound Trailer Jack That Has Mounting Hardware

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching