Replacement Lead Jack Leg for Stromberg Carlson Landing Gear

Question

Question:

Ok the weld stops are 15 1/2 inches how much for the replacement leg please

asked by: Mike S

0

Expert Reply:

If you have the Stromberg Carlson landing gear, part # LG-1, then the replacement lead leg is part # LG-179013. Since you already have the standard 15-1/2 inches between the weld stops on your current jacks you won't need to move the brackets on your trailer.

expert reply by: Charles S

0

Answer 1

Your 2008 Weekend Warrior 5th wheel trailer is pretty heavy. In my research I found the weight of the trailer is arouns 10,000 to 11,000-lbs so I recommend going with a system that can handle the weight. I recommend the Ultra-Fab Deluxe Electric…

view full answer...

Answer 2

To choose the correct landing gear replacement for your 2021 Cherokee Wolfpack 365pack16 Toy Hauler you will first need to find the correct rated weight capacity. Your trailer has a listed GVWR of 16,825lbs. Since each landing gear will only be…

view full answer...

Answer 3

When a landing gear leg fails, the most common cause is the gears. The gears for your LG-1 landing gear legs will be located at the top of the legs. If you do not have access to the top of the leg with it mounted to the trailer, then you will have…

view full answer...

Answer 4

It sounds like you are thinking about going with the Ultra-Fab Deluxe Electric Landing Gear Set #UF17-943010 as a replacement landing gear set for your 1996 Carriage Carri-Lite Cashay 28RK. The Ultra-Fab Deluxe Electric Landing Gear Set #UF17-943010…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 7

We do carry the 33" Ark Stabilizer Jack that you are looking for with part #ARK77FR. I was able to track down a few drawings that you should find helpful. These are for the 30" #ARK94FR and the 24" #ARK34FR Stabilizer jacks. I'm…

view full answer...

Answer 8

The 30" Ark Drop Down Corner RV Stabilizer Jacks #ARK94FR have a weld on design. This is the only way to install the jacks with the included mounts as there is not enough room between the stabilizer itself and the mounting plate for additional…

view full answer...

Answer 9

The weld-on mounting bracket for the ARK #AR94FR Drop Down Corner RV Stabilizer Jacks measures 4-5/8 x 2-7/8 inches. The bracket has holes for the hardware that attaches the jack to the brackets. The holes are 2-7/8 inches apart on center. I've…

view full answer...

Answer 10

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 11

I have included a picture showing how the motor and switch wire up on the Lippert stabilizer jack #LC298707.

view full answer...

Answer 12

The Dometic RV Water Heater - Gas - Automatic Pilot - 12 Volt - 8,800 Btu - 6 Gal Tank Item AT96121 is the direct replacement for the GC6AA-10E. Unfortunately it is out of stock with no expected restock date. Instead I recommend the Furrion RV…

view full answer...

Replacement Lead Jack Leg for Stromberg Carlson Landing Gear

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching