What is Distance Between Mounting Holes on Bottom of ComeUp DV-4500i Utility Winch

Question

Question:

Number of holes 2 or 4 and spacing of holes inches for mounting winch?

asked by: Ed Z

1

Helpful Expert Reply:

The mounting bolt pattern for the ComeUp Winch part # CU644512 that you referenced is two mounting holes that are separated by 3-11/16 inches.

expert reply by: Jameson C

1

Answer 1

The ComeUp DV-4500i Utility Winch #CU644512 would work well for you and have more than enough capacity since it has a 3,500 lb rated line pull. Which if you check out the chart I attached you will see that the amount of weight this winch can pull…

view full answer...

Answer 2

I have just what you will need. I have linked an FAQ article that explains the various ways to wire a winch. You will need the second half of the page titled Option 2: Wiring the Winch to a Separate, Trailer-Mounted Battery. I have also included a…

view full answer...

Answer 3

The Comeup Winch part #CU645010 and the Superwinch S5500 Trailer Winch #SW1455201 with the wireless remote #SW43GR are both pretty similarly specced once you have the wireless remote for the Superwinch. Based on that I would go with the ComeUp since…

view full answer...

Answer 4

Although the winch you referenced does not have free-spooling, there is a very similar winch that does. I recommend checking out the Bulldog Winch Powersports Series ATV Winch #BDW15011 which has a free-spooling clutch, load-holding brake and 1.2 hp…

view full answer...

Answer 5

While we do have a U.S.A. made option, the Bulldog Winch #BDW15018 is made in China. For a great American alternative, the highest capacity U.S.A. made winch we have is the Dutton-Lainson StrongArm Electric Winch w/ Pulley Block, AC Powered #DL24876.…

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 9

It is plastic. The ComeUp UW-5000si Trailer Winch item #CU645010 is a light duty winch so it's housing and base are made of plastic. I attached a picture below that will show you the base. I've also linked an installation video that will go…

view full answer...

Answer 10

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 11

Trailer wheel bearings are specific to the spindle that is installed on the axle that is on your trailer. You will need to safely support the trailer, remove the wheel and tire, remove the grease cap, remove the cotter pin and washer that secures the…

view full answer...

Answer 12

Load range B trailer tires are going to have a lower capacity than C load range tires. Basically that, psi rating, and the ply rating are the only differences. A higher load range tire would last a little longer than lower load ranges of the same…

view full answer...

What is Distance Between Mounting Holes on Bottom of ComeUp DV-4500i Utility Winch

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching