Could Curt TruTrack Weight Distribution System Fit Trailer with 6 inch Tall Trailer Frame

Question

Question:

Will the Curt TruTrack Weight Distribution System w/ Sway Control - Trunnion - 15,000, Item # C17501 work with an Intech trailer which has 3.5inch coupler offset, 5inch frame depth, and 6inch frame rail height?

asked by: Chris

0

Expert Reply:

Yes, since the Curt TruTrack part # C17501 has a max frame height of 6 inches and your frame is 6 inches tall this would work on your Intech trailer. If the frame is 5 inches wide you would need to source longer hardware for the brackets as well.

expert reply by: Jameson C

0

Answer 1

Weight distribution spring bar tension can be increased by tilting the head toward the trailer so that the ends of the spring bars are closer to the ground. Once connected to the lift brackets this increased angle translates into more tension, which…

view full answer...

Answer 2

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 5

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 6

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 7

For your 2018 Ram 2500 with the factory puck system the best 5th Wheel Hitch is the B&W OEM Companion. If you have the 8 foot bed then you will want the fixed 25K #BWRVK3600 and if you have the short 6-1/2 foot bed you will need the 20K Slider…

view full answer...

Answer 8

If you are just looking for a new converter, the Replacement Converter for Parallax/Magnetek or WFCO RV Power Centers part #PD4635V will be a direct upgrade for the Magnetek Converter Series 6300 Model 6332 that you have now.

view full answer...

Answer 9

For sag from towing a trailer the best recommendation I can make is actually a weight distribution system. Suspension enhancement will help level your truck while towing. But the advantage to a weight distribution system is that it levels the vehicle…

view full answer...

Answer 10

Generally speaking, it is not advisable to reverse a trailer when using a weight distribution system. The system won't blow up but if you reverse at too sharp an angle then you can damage the head so you have to do so in a pretty straight line or…

view full answer...

Answer 11

It sounds like the purpose of getting the air helper spring would be to counteract the 1 inch compression you're getting in your rear suspension caused by the pin weight of your 5th wheel. If that's the case, I believe that the AirLift 5000…

view full answer...

Answer 12

Based on the available information for your 2022 Airstream Flying Cloud 30FB it looks like you have Dexter #11 Torflex axles. Assuming that is accurate, you need the Torflex Lift Kit - Tandem Axle - 2-7/8" Lift #K71-724-02. I recommend verifying…

view full answer...