Trailer Ball Height to Increase Tongue Weight to Help with Sway Control on a Single Axle Fish House
Question:
I have a 16 ice castle single axel fish house that sways quite a bit. I have an adjustable hitch on my pickup and I would like to know, do I raise or lower the height of the ball to increase tungue weight?
asked by: Lyle B
Expert Reply:
You should have the hitch ball height set so that the trailer tows as level as possible behind your pickup. If there is a setting that goes between slightly higher than level and slightly lower than level, opt for the slightly lower setting, when the trailer is sitting on the trailer ball.
An increase in tongue weight will most likely help with your sway situation. Adding weight in front of the trailer axles would be the best way to increase the tongue weight, just make sure you stay within the capacities of your towing setup.
If you still have issues with sway after correctly setting the ball height and adding weight to the front of the trailer, you might want to consider adding a sway control unit and bracket. You could use the Reese Friction Sway Control Kit, # 83660, along with a Reese Sway-Control Bracket, # RP26003, if your adjustable ball mount will accommodate the sway control bracket.
We have a section in our weight distribution article that explains this type of sway control for you to review, see link.
Products Referenced in This Question
Reese Friction Sway Control Kit - Economy - by Draw-Tite, Reese and Hidden Hitch
- Accessories and Parts
- Weight Distribution Hitch
- Sway Control Parts
- Reese
more information >
Product Page this Question was Asked From
Reese Sway-Control Bracket for 2" Ball Mounts - Class III and IV
- Accessories and Parts
- Weight Distribution Hitch
- Adapters
- Sway Control Parts
- Brackets
- Reese
more information >
Featured Help Information
Instructions
Miscellaneous Media
Continue Researching
- Shop: Suspension Enhancement
- Shop: Air Lift WirelessONE Compressor System for Air Helper Springs - Remote - Bluetooth - EZ Mount
- Shop: Air Lift LoadLifter 7500 XL Ultimate Air Helper Springs - Rear Axle
- Shop: Air Lift LoadLifter 5000 Air Helper Springs - Rear Axle
- Shop: SuperSprings Custom Suspension Stabilizer and Sway Control Kit - Factory Leaf Springs Above Axle
- Shop: Air Lift Union Tee for 1/4" Air Lines
- Shop: Trailer Hitch
- Shop: Gen-Y Hitch Shock Absorbing 5th Wheel to Gooseneck Pin Box - Lippert 1621/1621HD - 30K GTW - 4.5K TW
- Shop: Brake Controller
- Shop: etrailer Tongue Weight Scale for Campers and Utility Trailers - 2,000-lb Capacity
- Search Results: weight distribution hitch
- Q&A: Will the Dometic Ultra Breeze Trailer Roof Vent Cover Work with Existing Flange on Dometic Fan
- Search Results: gen~y hitch
- Article: Determining Trailer Tongue Weight
- Shop: Front Mount Hitch
- Q&A: Can Fastway E2 # FA94-00-0800 be used with Jayco Hummingbird 17RB
- Video: Review of CURT Weight Distribution Hitch - MV Weight Distribution System - C17050
- Video: Draw-Tite Front Mount Trailer Hitch Installation - 2018 Ford F-150
- Search Results: weight distribution sway control
- Search Results: fastway e2 hitch
- Q&A: Replacement Tires for Forest River Rockwood Geo Pro G19FD with ST235/75-15 Tires
- Search Results: e100
- Q&A: Can a Trailer Ride With the Tongue at an Upward or Downward Angle
- Search Results: 2 inch hitch receiver
- Search Results: trailer breakaway kit
- Video: Review of Dometic RV Vents and Fans - Ultra Breeze Black Trailer Roof Vent Cover - DMC38FR
- Video: Coil SumoSprings Rear Axle Helper Springs Review
- Video: Review of Equal-i-zer Replacement Head For Equal-i-zer Weight Distribution Systems - EQ90-02-1200
- Article: The Best Trailer Tongue Locks for Preventing Trailer Theft
- Q&A: Correct Coil SumoSprings Custom Helper Springs for 2022 Subaru Outback Wagon Wilderness
on Accessories and Parts
Mark K.
6/5/2020
i have a 23 ft trailer with a 22 ft i/o. the entire package weighs 5500 lbs. while towing, i experienced major trailer sway. i measured the tongue weight and it was only 220 lbs. i moved the boat forward as far as i could, (2.5 inches) and it increased to 330 lbs. my next step is to move the axle more to the rear. do you think i can assume a rule of thumb in my case, that 2.5 inches of weight moving forward will gain 110 lbs? or is there another way to figure out how far to move it, or just do a little at a time and measure along the way? my trailer total length is 23 ft 3 inches, with the transom even with the trailer and the outdrive and wood swim platform overhanging. thanks for any advice you can give me,