Can Inner Legs of Ultra-Fab Deluxe Electric Landing Gear Set # UF17-943010 Rotate

Question

Question:

I am curious if the Jacks can be installed so that the weld stops are facing across the trailer? Meaning can the pin tubes be rotated inside the Jack? It appears as though there is a hole on what would be the front side of the Jack tube in the pictures?

asked by: Chris

0

Expert Reply:

Yes, if you wanted to remove the inner legs of the Ultra-Fab Deluxe Electric Landing Gear Set # UF17-943010 that you referenced you could and then reinstall them rotated 90 degrees.

expert reply by: Jameson C

0

click to enlarge

Answer 1

Sure thing! The Ultra-Fab Deluxe landing gear, part #UF17-943010, wiring is actually pretty straightforward once you know which wire is which by color. The switches and the motors both have red and black wires. Those need to be connected to each…

view full answer...

Answer 2

The first thing to do is to make sure you are getting sufficient power to the motor and a good ground. If you have checked the wiring and still experience the motor cutting out I do recommend to replace it with Lippert Components Venture 5th Wheel RV…

view full answer...

Answer 3

The Atwood 87701-SP three-switch panel that you referred to is now obsolete, no longer made, and none in stock. The only wiring information I could find for you is a poor quality drawing from Atwood/Lippert which I have attached. We do not have this…

view full answer...

Answer 4

The squeaking noise on your trailer is probably coming from the joints in the suspension creating metal to metal friction. So, unless your original Equa-Flex Cusioned Equalizers are damaged or corroded, what will make the biggest difference is to…

view full answer...

Answer 5

Is the battery of the breakaway kit charged? Does your tow vehicle have a brake controller installed?

view full answer...

Answer 6

The best option we offer for your dump trailer is the Erickson Mesh Tarp and Truck Bed Cover part #EM57059 which measures 12' wide x 16' long. It's not the exact dimensions you wanted but it will still cover most of the area you need it…

view full answer...

Answer 7

The part you referenced 127194TB is a double-lip seal with an inner diameter of 1.274-inches and an outer diameter of 1.983-inches. The available seal nearest to those dimensions that we offer is part #RG06-010, which is a double-lip seal sold as a…

view full answer...

Answer 8

A TCM double-lip grease seal number 127194 has an inner diameter of 1.274-inches and an outer diameter of 1.983-inches according to my research. The available grease seal nearest to those dimensions that we offer is part #RG06-010, which is a…

view full answer...

Answer 9

The 18.5x8.5-8 is actually an old tire size that is not used much anymore. The closest metric size to your existing tire would be 215/60-8. Your wheel most likely has a 5-on 4-1/4 inch bolt pattern (see link), you will want to make sure that the bolt…

view full answer...

Answer 10

The 1-7/8 inch width is what is rounded up to 2 inches which is a standard width for winch straps. The 14 foot length is not something we carry. I recommend the Hand Winch Strap with Safety Hook, 2" Wide x 15' Long - 4,000 lbs #DL24239 or…

view full answer...

Answer 11

I would love to help you upgrade the suspension on your Twilight 2800 travel trailer. The MORryde Rubber Equalizers for Tandem Axle Trailers #MR87ZR that you referenced are a great solution but we do need to double check a few things. First is that…

view full answer...

Answer 12

You will need the Ceiling Garnish for Fan-Tastic Vents Roof Vent #FVK1060-81 as it is specific to your Dometic Fantastic Fan 1450. The Ceiling Garnish for Ventline Roof Vent #VA0445-37 is going to have rounded corners as opposed to the square on the…

view full answer...

Can Inner Legs of Ultra-Fab Deluxe Electric Landing Gear Set # UF17-943010 Rotate

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching