Thread Size for Let's Go Aero Anti-Rattle Trailer Hitch Receiver Lock # 63232

Question

Question:

What size are the threads on this part? What is the diameter of the shoulder above the threads?

asked by: Dd

0

Expert Reply:

The threads of the Let's Go Aero Anti-Rattle Trailer Hitch Receiver Lock # 63232 have a 5/8 inch diameter with 11 threads per inch. The shoulder just above the threads has the same 5/8 inch diameter.

I have attached a short video review on this product that you can check out as well.

expert reply by: Chris R

0

Answer 1

E-tracks are typically the stronger of the two, but X-track is more versatile since you can mount them horizontally or vertically. Choosing between the two really depends upon how you plan to use them. If you are installing something in a truck…

view full answer...

Answer 2

When it comes to your rear cargo carrier, I recommend The Threaded Anti-Rattle Hitch Pin Lock for etrailer Cargo Carriers #e99047 if you have an Etrailer brand cargo carrier and that is due to the pin hole having a different diameter then the other…

view full answer...

Answer 3

If you are trying to get the swing away adapter that is closest to the vehicle's bumper, here are the measurements to the closest part of the rack from the shank receiver pinhole: Kuat Pivot 2 Swing Away Hitch Extender for Bike Racks #PVP20B:…

view full answer...

Answer 4

The distance from the hitch pin hole of the Saris Swing Away Hitch Extender part #SAR36VR to the other hitch pin hole is 13-1/2 inches.

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 9

Normally trailer coupler height is around 17 inches, from the ground to the bottom of the coupler, and most hitch manufacturers design their hitches to work with a ball mount that will end up very close to this measurement. I am including a link to…

view full answer...

Answer 10

Hey Buddy, so the Fastway Adjustable Ball Mount part #DTSTBM6825-2S is a really great choice for the 2-1/2 inch hitch of your 2021 Ford F-250 which is going to be very solid in your hitch due to it's built in anti-rattle device that is easy to…

view full answer...

Answer 11

There is a way for you to not only lock the B&W Tow & Stow 3-Ball Mount - Compatible with GM MultiPro Tailgate - 2.5" Hitch - 148K #BWTS20067BMP to your 2-1/2 inch trailer hitch, but also the ball platform to the mount, and the hitch…

view full answer...

Answer 12

Thank you for the photos and sorry to hear about your truck! The unique design of the B&W Tow & Stow 2-Ball Mount - Compatible with GM MultiPro Tailgate #BWTS20066BMP is that angled section that meets with the shank part of the ball mount. On…

view full answer...

Thread Size for Let's Go Aero Anti-Rattle Trailer Hitch Receiver Lock # 63232

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching