Can a 2007 Hyundai Accent Pull a Trailer and What Parts Are Needed

Question

Question:

Would it handle a golf cart on a trailer

asked by: James

0

Expert Reply:

The Curt Trailer Hitch Receiver part # C11094 which is a fit for your 2007 Hyundai Accent (Sedan) has a maximum gross trailer weight rating of 2,000 lbs. Therefore, so long as the weight of the golf cart and trailer do not exceed this figure which I think is reasonable to assume and the vehicle is rated high enough then yes, you can use this hitch to tow a golf cart on a trailer.

In order to complete your towing setup you are also going to need a trailer wiring harness, the Hopkins Plug-In Simple Vehicle Wiring Harness with 4-Pole Flat Trailer Connector part # HM11143944 which is the only plug and play harness available for your vehicle and a ball mount/hitch ball, the Curt Class II Drawbar part # C45521 with the 1-7/8" Hitch Ball part # 19256 or the 2" Hitch Ball part # 19258.

expert reply by: Conner L

0

Answer 1

All of the hitches available for the 2008 Hyundai Accent are Class I 1-1/4 inch hitch receivers because of its limited towing capacity. The Accent's weight capacity is 849 pounds including cargo, occupants and tongue weight. The hitch…

view full answer...

Answer 2

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 3

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 4

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 5

What you're going to need is two of the transfer switches in that case. I have attached a diagram from Furrion that shows you how you're going to need to hook the two transfer switches #F30ATS up: -one to the other, then one branching off to…

view full answer...

Answer 6

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 7

The old version of the #HBA-CAM used 4 wires, but the product was updated awhile back and now uses only two wires as shown in the photo on the product description page. The white wire from the HBA-CAM would tap into the white ground wire and the blue…

view full answer...

Answer 8

If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…

view full answer...

Answer 9

Since Demco uses 3,500 drum brake assemblies part #DMSB24429M and #DMSB24428M what you'd need is similar 3,500 electric brake assemblies like the etrailer part #AKEBRK-35L-SA for the left hand side and #AKEBRK-35R-SA for the right hand side. To…

view full answer...

Answer 10

If you are installing just the Firestone Ride-Rite kit, #F2400, and not also adding an on-board air compressor such as #F2158, then I would estimate that it should take about 2 hours to install the kit. That is for someone with some mechanical…

view full answer...

Answer 11

I would be happy to help you set up your 2022 Toyota Highlander to haul your new travel trailer. The wiring harness you currently have controls your trailer's lighting functions only. You do not need to rewire your Toyota you just need another…

view full answer...

Answer 12

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Can a 2007 Hyundai Accent Pull a Trailer and What Parts Are Needed

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching