Rack'em Grass Catcher Compatible with Toro Zero Turn Mower

Question

Question:

Will this grass catcher fit a 52 inch Toro Z mower

asked by: Christy J

0

Expert Reply:

The Rack'em Grass Catcher for Toro Lawn Mower with Z-Cut Deck # RCMMS4-EXS1-TORO will fit your 52 inch Toro Z mower deck if it has the Z-cut deck. If you have the regular deck then you will use # RCMMS4-EXS1 instead.

The best way to determine that fit is to look at the discharge on your deck. The Z-cut will have little cutouts on the front and middle directly on the lip that is raised about 1-1/2 inches. If that lip does not have any cutouts then it is the regular deck. I've attached a photo to help determine if you have the Z-cut like what is shown.

expert reply by: Jason S

0

click to enlarge

Answer 1

So normally for a Wright Stander mower you'd want the RackEm grass catcher part #RCMMS4-BS2 and for the Toro 52 grandstand you'd want the #RCMMS4-EXS1-TORO. What you could do is use the #RCMMS4 which fits both as the main catcher assembly and…

view full answer...

Answer 2

If your Toro Timecutter has the Z cut deck that extends out further than the rear wheel, you'd use the Rack 'Em #RCMMS4-EXS1-TORO catcher. If you have the regular deck, you'd use #RCMMS4-EXS1. The Z deck has notches or slots in it as…

view full answer...

Answer 3

If your Toro Timecutter has the Z cut deck that extends out further than the rear wheel, you'd use the Rack 'Em #RCMMS4-EXS1-TORO catcher. If you have the regular deck, you'd use #RCMMS4-EXS1.

view full answer...

Answer 4

The correct catcher will depend on the discharge opening behind that deflector shown in your photo. If it has the deck with a Z-bracket as shown in the provided photo, you'd use #RCMMS4-EXS1-TORO. If it doesn't have the z-slot, but has a 4…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

If your Toro Titan HD has a regular deck you need the #RCMMS4-EXS1. If you have the Z-Cut deck you need the #RCMMS4-EXS1-TORO instead. If your deck isn't one of these two you could still use the Rack'Em Multi-Mount Grass Catcher #RCMMS4 but…

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

The Rack'em Grass Catcher for Scag Lawn Mower with Velocity Deck #RCMMS4-OVBS1 comes with the faceplate you need along with all hardware needed for installation. The extension you are seeking is the Extension for Rack'em Multi-Mount Grass…

view full answer...

Answer 9

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 10

The correct Grass Catcher for your Scag Liberty Z48 is the part #RCMMS4-OBS1.

view full answer...

Answer 11

You are a little on the warm side for your transmission fluid. If you can keep it under 200 degrees you will have the max life out of it. That being said transmissions really start to go downhill at 260 degrees. The Derale cooler part #D13503 with…

view full answer...

Answer 12

The best hitch I'd recommend for your 2011 Chevy Silverado is the Curt hitch part #14301 because it has great towing capacities at 10,000 lb trailer weight and because it has only the hitch tube that hangs below the rear bumper for a more…

view full answer...

Rack'em Grass Catcher Compatible with Toro Zero Turn Mower

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching