Do Retrax Replacement Clamps Fit RetraxPRO Cover Without Stake Pockets

Question

Question:

Hello , i have a retrax pro bed cover with no cut out stakes , for 2015 ram regular cab with 6.5foot bed , Dose these clamps fit for this retrax cover ? Thank you

asked by: AHMAD A

0

Expert Reply:

Yes, the Retrax Replacement Clamps # RTX34FR will work on your RetraxPRO cover that does not have the stake pocket cutouts. I confirmed their fit on your Ram with 6-1/2-foot bed with my contact at Retrax.

expert reply by: Adam R

0

Answer 1

Since you have a RetraxPro tonneau cover the correct replacement lock assembly you need is the part #RTF05-1014 and you'd be set. You'll need to enter the serial number you provided on the product page for the lock assembly.

view full answer...

Answer 2

We have the Replacement Clamps for Retrax Hard Tonneau Covers #RTX34FR that fit the following covers. RetraxONE MX RetraxONE XR RetraxPRO MX RetraxPRO XR PowertraxONE MX PowertraxONE XR PowertraxPRO MX PowertraxPRO XR The kit includes installation…

view full answer...

Answer 3

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 4

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 5

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 6

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 7

I would be happy to help you set up your 2022 Toyota Highlander to haul your new travel trailer. The wiring harness you currently have controls your trailer's lighting functions only. You do not need to rewire your Toyota you just need another…

view full answer...

Answer 8

If your vehicle has a factory brake controller plug, you can simply use the Tekonsha Plug-In Wiring Adapter for Electric Brake Controllers – Ford, Item #3034-P, which will connect to the vehicle plug and the brake controller. On the new E-450…

view full answer...

Answer 9

If the trailer wheels scrubbed (dragged and scrapped the ground instead of rolling) when jack knifed then it could have thrown something out of alignment or damaged something. First, inspect the suspension. Look for any elongated holes where…

view full answer...

Answer 10

To see all of the correct wheel and tire combos you'd need check out the link I attached. The option I would recommend is the part #TA43RR which is a Load Range C tire size ST175/80R13 mounted on a white spoke wheel with a bolt pattern of 5 on…

view full answer...

Answer 11

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Answer 12

I have a solution for you, but we do not carry Glo-Brite lights, so replacing it with the same brand will not be something I can offer you. Instead, to replace your Glo-Brite 9852-88, I recommend using the Optronics LED Trailer Tail Light #STL72RB.…

view full answer...

Do Retrax Replacement Clamps Fit RetraxPRO Cover Without Stake Pockets

Product Page this Question was Asked From

Continue Researching