Replacement Yakima Hex Wrench Recommendation for Yakima Ski Rack

Question

Question:

I have an old Yakima ski rack on my Subaru Outback 2011. I purchased the rack in 2013. I have round crossbars and a 4 ski rack on top. I lost the hex wrench that undoes the ski rack from the round crossbars. Do you know what size I need?

asked by: Teressa

0

Expert Reply:

For a replacement Yakima hex wrench we have the part # 8880143 which is the size of 5 mm.

expert reply by: Jameson C

0

click to enlarge

Answer 1

You have the Yakima Control Towers with round crossbars. In one of the pictures you can make out the Yakima logo on the base of the tower. The tightening tool for this is a 5 millimeter hex wrench, part #8880143.

view full answer...

Answer 2

For your Thule snowboard carrier 91725B the correct tamperproof tool is actually the part #853-5270-02.

view full answer...

Answer 3

Yes, the Replacement 5/32" Hex Wrench for Yakima Rooftop Carriers - Tamper Proof item #8880818 also works on the Yakima FreshTrack 4.

view full answer...

Answer 4

If the key number isn't on the face of the lock, it'll be engraved into the side of the lock core. If the lock is unlocked, you can use the Yakima Control Key #Y8007835 to remove the lock core and get the code number off the side. You'd…

view full answer...

Answer 5

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 6

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 7

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 8

The old version of the #HBA-CAM used 4 wires, but the product was updated awhile back and now uses only two wires as shown in the photo on the product description page. The white wire from the HBA-CAM would tap into the white ground wire and the blue…

view full answer...

Answer 9

To see all of the correct wheel and tire combos you'd need check out the link I attached. The option I would recommend is the part #TA43RR which is a Load Range C tire size ST175/80R13 mounted on a white spoke wheel with a bolt pattern of 5 on…

view full answer...

Answer 10

I have a solution for you, but we do not carry Glo-Brite lights, so replacing it with the same brand will not be something I can offer you. Instead, to replace your Glo-Brite 9852-88, I recommend using the Optronics LED Trailer Tail Light #STL72RB.…

view full answer...

Answer 11

The 40 amp fuse for your 2006 Chevrolet Silverado tow package is used for the 12 volt battery charge circuit. This fuse is located toward the front of the underhood fuse box closest to the front auxiliary positive post (see photo). There may be a…

view full answer...

Answer 12

On a 2005 Chevy Silverado 1500, If you are facing the front of the truck looking at the power distribution box, there will be a post at the back left side and a fuse slot near it. It is that fuse slot that you will install a 30 amp fuse. I have…

view full answer...

Replacement Yakima Hex Wrench Recommendation for Yakima Ski Rack

Product Page this Question was Asked From

Continue Researching