Which Way Does Wheel Rim Clamp # 15-2 Go on Rear Wheel of Mobile Home

Question

Question:

Which way do hub clamps go on rear wheel of mobile home

asked by: Javier

0

Expert Reply:

The Wheel Rim Clamp # 15-2 that you referenced will install with the lip towards the inside of the hub on the other side of the nut that holds it in place. The angled portion of the clamp sits outside of the wheel and it will tighten up against it as you turn the nut.

We don't have any pictures available of this particular clamp installed and it's a little hard to describe it but if you search for some images online of a wheel rim clamp installed you might get a clearer picture as to how it works.

expert reply by: Chris R

0

Answer 1

I spoke with my contact at Redline and he said the Wheel Rim Clamp for Mobile Home Style Hubs #15-2 goes towards the hub. So the flat side of it goes up against the lug nut.

view full answer...

Answer 2

On the Wheel Rim Clamp for Mobile Home Style Hubs, #15-2, the portion with the lip goes toward the inside of the hub and opposite the nut. The angled side goes to the outside of the wheel so as you tighten the nut it pushes against the lip on the…

view full answer...

Answer 3

Typical torque rating for car, truck and SUV lugs is 90 ft. lbs. As always, you should check with the manufacturer of the mobile home for proper ratings. Vehicle weight, lug type, hub type, etc. all play a role in the torque rating and the best way…

view full answer...

Answer 4

Redline's Wheel Rim Clamps, part #15-2 is the replacement clamp for your Dexter Hub and Drum Assembly #8-174-5UC3. You can purchase them individually. We also offer the hex nuts separately because they seem to occasionally disappear during the…

view full answer...

Answer 5

Both the Curt #C13382 and the etrailer #e98912 hitch are a 2" Class III hitch receiver that will provide a maximum gross trailer weight of 3,500 lbs and a maximum tongue weight of 525 lbs. You are correct, they are an identical hitch but our…

view full answer...

Answer 6

What you'll want to do is refer to your instructions for the proper torque specs. For example, the instructions for the 5.2K - 6K Kodiak Disc Brake Kit #K2HR526D call for the brake mounting flange to be welded to the spindle and then the caliper…

view full answer...

Answer 7

I went to our warehouse to measure the Replacement Adjuster Spring for Dexter Electric Brake Assembly #BP08-155 for you. The length of the spring is 4.14 inches and the width is .43 inches. I've attached a photo to assist.

view full answer...

Answer 8

The torque for the Dexter Trailer Hub and Drum Assembly - 6,000-lb and 7,000-lb Axles - 12" - 5 Spoke Utility #8-174-5UC3 is not specified by the manufacturer. For 9/16 inch studs, the typical lug nut torque will be 120-140 ft lbs based on most…

view full answer...

Answer 9

Currently we only offer these parts as individual items and not as a set for mounting your mobile home wheels to the hubs. 9/16" Wheel Rim Clamp #15-2 9/16" Hex Nut #916N 9/16" X 3" Trailer Hub Wheel Stud #25-11

view full answer...

Answer 10

On the Wheel Rim Clamp for Mobile Home Style Hubs, #15-2, the portion with the lip goes toward the inside of the hub and opposite the nut. The angled side goes to the outside of the wheel so as you tighten the nut it pushes against the lip on the…

view full answer...

Answer 11

The Dexter Trailer Hub and Drum Assembly - 6,000-lb and 7,000-lb Axles - 12" - 5 Spoke Utility #8-174-5UC3 are the only hubs we have with that bolt pattern to fit your wheels. Based on the measurements you gave, you will then use the Dexter…

view full answer...

Answer 12

To determine if there are compatible hubs and associated bearings to replace your current hubs to a more standard size you will have to take several precise measurements on the spindle of your axle. It is recommended to use a set of dial calipers to…

view full answer...

Which Way Does Wheel Rim Clamp # 15-2 Go on Rear Wheel of Mobile Home

Product Page this Question was Asked From

Continue Researching