Sidewinder Wedge Recommendation for Use with Reese Fifth Wheel Hitch with Double Jaw

Question

Question:

Reese double jaws which wedge would I need

asked by: Jason

0

Expert Reply:

For a double jaw Reese fifth wheel hitch the correct Sidewinder wedge is the part # SWW-03.

expert reply by: Jameson C

0

Answer 1

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 2

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 3

Hey Jay. It sounds like you are on the right track here because a sidewinder pin box will be your only option for pulling your 5th wheel since you have a short bed truck with the Rambox. That said, you are right that the Reese Sidewinder cannot be…

view full answer...

Answer 4

Choosing the right height setting for your 5th wheel hitch is a combination of a few different variables. First of all you want your towing setup to be as level as possible. With your Montana High Country 340BH level you will want to measure from the…

view full answer...

Answer 5

The head alone for the B&W Companion hitch #BWRVK3500 weighs about 70 pounds. Everything else weighs about 130 pounds. So the total weight of the hitch is approximately 200 pounds.

view full answer...

Answer 6

The Ram OEM 5th wheel puck system, shown in the linked photo and article, was launched in 2013 so what you have in your truck is likely to be an aftermarket installation of some kind. These newer Ram trucks with the factory prep can directly accept a…

view full answer...

Answer 7

The B&W Companion OEM 5th Wheel Hitch w/ Slider for Chevy/GMC Towing Prep Package #BWRVK3775 you're looking at will work fine with your new Chevrolet Silverado. This hitch has 3 height adjustments so you'll be able to set the hitch height…

view full answer...

Answer 8

If you take a look at the linked diagram you can see the minimum recommended clearance distances between truck and trailer for 5th wheel towing. It is recommended to have at least 5-inches from the top of the bed rails to the bottom of the trailer…

view full answer...

Answer 9

You do not have to use a sliding 5th wheel hitch in a short bed truck. In many cases, truck beds shorter than 8 ft do not have enough clearance between the trailer and truck to execute sharp turns. This is why sliding hitches were invented. Due to…

view full answer...

Answer 10

A wedge is needed, yes, and the Lippert Turning Point pin box does come with a universal wedge, but it is not a very good fit with the B&W Companion #BWRVK3710. So I highly recommend instead using the 5th Airborne Custom Wedge for B&W Fifth…

view full answer...

Answer 11

There are a couple of options that'll work great with your Lippert Turning Point Pin Box, however one hitch stands out to me more than others. Take a look at the: -Curt E16 5th Wheel Trailer Hitch - Slide Bar Jaw - 16,000 lbs #C16115 This 5th…

view full answer...

Answer 12

The Patriot Slider part #BWRVK3270 might be a bit more noisy than the Companion slider part #BWRVK3400 due to the increased number of mounting points, 4 at the corners vs. 1 in the center. Probably not that noticeable and certainly not something…

view full answer...

Sidewinder Wedge Recommendation for Use with Reese Fifth Wheel Hitch with Double Jaw

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching