Replacement Fan Blades for RV Ceiling Fan

Question

Question:

I have a 2015, 38 1/2 foot wildwood lodge park model trailer and need replacement ceiling fan blades. What are the proper size?

asked by: Dave

0

Expert Reply:

Since RV makers don't keep track of smaller items like the fans and vents they install there is no way to look up the specific unit you have but if you check the fan you can usually find a manufacturer name and part number.

The replacement ceiling fan blade kit we offer is part # 277-000398 (a set of four). These blades have two finishes, cherry and maple, on the two sides.

We also offer both complete 12V fans like hugger style # 344410TSDC36BNOKCY.

expert reply by: Adam R

0

Answer 1

I measured the Replacement Blades for AirrForce 42" Hugger Style RV Ceiling Fan #277-000398 for you and they are 16- 5/8 inches long with 4 inches wide at the bottom and 4-7/8 inches wide at the top. I've attached a photo to assist.

view full answer...

Answer 2

Would you be able to find out the model of your fan? The Replacement Blades #277-000398 are the only blades that we currently carry (as of Sept 2018) and they measure 16-5/8" long. These are a replacement for the 42" Hugger Style RV…

view full answer...

Answer 3

According to the manufacturer the #277-000399 replacement brackets will probably work for a AirrForce 42" hugger-style 4-blade ceiling fan without a light. They said they believe the same brackets are used for both. Since there is some…

view full answer...

Answer 4

The Replacement Fan Blades #277-000398 are 16-5/8-inches long. They measure 4-7/8-inches wide at their widest point and 4-inches wide at their narrowest point. These install onto brackets like #277-000399 which then attach to the fan itself.

view full answer...

Answer 5

The Replacement Brushed Chrome Brackets for AirrForce RV Ceiling Fan with Light - Qty 4 #277-000399 does match the 1-1/2" and 3-7/16" measurements provided, so you can use these on your ceiling fan. If you also need new fan blades,…

view full answer...

Answer 6

What you are looking for is the Replacement Blades for AirrForce 42" Hugger Style RV Ceiling Fan #277-000398. These are the exact replacements for the 42" Hugger Style RV Ceiling Fan.

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 9

You are correct that this refrigerator does not have an ON/OFF switch or function. The best you can do is "Standby" that draws an unknown amount of power. One option is to pull the 12-Volt fuse at the RV power center. A much better option…

view full answer...

Answer 10

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 11

From what I could find it looks like your 122R (red) and 122Y (amber) lights measure 3.75" x 1.70" x .81". We don't have any replacement lense directly for the GLO-BRITE lights but we do have some similar lights that you could use…

view full answer...

Answer 12

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...