Replacement Blades for Hugger Style RV Ceiling Fan

Question

Question:

I need a blade for this fan. Can you help? 42inch Hugger Style RV Ceiling Fan with Light Kit for RVs - Brushed Chrome Item # 277-000081

asked by: Don V

0

Expert Reply:

What you are looking for is the Replacement Blades for AirrForce 42" Hugger Style RV Ceiling Fan # 277-000398. These are the exact replacements for the 42" Hugger Style RV Ceiling Fan.

expert reply by: Kyle S

0

Answer 1

The overall length of the Replacement Fan Blades for AirrForce 42" Hugger Style Ceiling Fan #277-94444 that you referenced is 16-5/8 inches.

view full answer...

Answer 2

Since RV makers don't keep track of smaller items like the fans and vents they install there is no way to look up the specific unit you have but if you check the fan you can usually find a manufacturer name and part number. The replacement…

view full answer...

Answer 3

The Replacement Fan Blades #277-000398 are 16-5/8-inches long. They measure 4-7/8-inches wide at their widest point and 4-inches wide at their narrowest point. These install onto brackets like #277-000399 which then attach to the fan itself.

view full answer...

Answer 4

I measured the Replacement Blades for AirrForce 42" Hugger Style RV Ceiling Fan #277-000398 for you and they are 16- 5/8 inches long with 4 inches wide at the bottom and 4-7/8 inches wide at the top. I've attached a photo to assist.

view full answer...

Answer 5

The Replacement Brushed Chrome Brackets for AirrForce RV Ceiling Fan with Light - Qty 4 #277-000399 does match the 1-1/2" and 3-7/16" measurements provided, so you can use these on your ceiling fan. If you also need new fan blades,…

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two…

view full answer...

Answer 8

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 9

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion…

view full answer...

Answer 10

Yes, I have listed for your below the roof rack systems from Rhino-Rack, Thule, and Yakima that will fit the RetraxPRO XR Hard Tonneau Covers like part #RTT-80243 for your 2019 Ram 1500. Rhino-Rack Vortex Crossbar System part #RRVA180B-RRRLT600…

view full answer...

Answer 11

The best hitch for a 2024 Subaru Outback is the etrailer item #e25TR. This hitch is custom fit and bolts to your Subaru with included hardware. This is a class III hitch with a 2" receiver, that has a 3,500 lbs towing capacity and a 350…

view full answer...

Answer 12

Aside from a slight change in the appearance of the crossbar (the WingBar Evo has some boxed edges as opposed to the completely smooth front of the AeroBlade) the biggest differences are the rubber strip on top of the crossbar and the weight…

view full answer...

Replacement Blades for Hugger Style RV Ceiling Fan

Product Page this Question was Asked From

Continue Researching