Can Sections of Optronics Flexible LED Light Strip UCL90CB Be Re-Connected

Question

Question:

I have a 32’ 5th wheel that I will be adding these strips for various areas. If I cut down a 17’ to a 10’, can I use the extra 7’ somewhere else? If so, how does that work?

asked by: Keith

0

Expert Reply:

Yes, you can use any cut-off sections of the 17-Foot LED Strip Lights like # UCL90CB (white) and # UCL90BCB (blue) by adding Snap-On 12V Lead part # A90PB. In the same way part # A90P1B can be used to link two complete strips together.

Each complete 17-foot section will draw 2.7-amps.

expert reply by: Adam R

0

Answer 1

Yes, the Optronics Flexible LED Light Strip #UCL90CB does have wiring on both ends allowing you to cut the strip in 2. We also have the Optronics LED Light Strip 12-Volt Connector with Wire Leads #A90PB if you need to cut it into additional pieces.

view full answer...

Answer 2

Yes, the Optronics Flexible LED Light Strip part #UCL90CB can be cut to the desired length you need for your application. That said, there are cut lines on the strip you must use which are located every 2". Once the cut is made you can then…

view full answer...

Answer 3

When connecting the Optronics Flexible LED Light Strip #UCL90CB using the #A90P1B you just need to make sure that the colors on both sides of the connector match. Red to red and black to black.

view full answer...

Answer 4

I did some research on your cap LED light strips on your 2019 Grand Design Momentum 351M toy hauler. We do carry LED strips that are compatible. - Optronics Flexible LED Light Strip - Weatherproof - White #UCL90CB Also, if you need to connect two…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

From what I could find it looks like your 122R (red) and 122Y (amber) lights measure 3.75" x 1.70" x .81". We don't have any replacement lense directly for the GLO-BRITE lights but we do have some similar lights that you could use…

view full answer...

Answer 8

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 9

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 10

Load range B trailer tires are going to have a lower capacity than C load range tires. Basically that, psi rating, and the ply rating are the only differences. A higher load range tire would last a little longer than lower load ranges of the same…

view full answer...

Answer 11

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 12

To determine the size of the hub assembly you need to purchase you have to determine which bearings are in the old assembly. If the old assembly has L44649 inner bearings, you would use the hub you chose #8-258-5UC1. If the inner bearings are marked…

view full answer...

Can Sections of Optronics Flexible LED Light Strip UCL90CB Be Re-Connected

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching