Assembled Height of Timbren Active Off-Road Bumpstops # TABSOSR

Question

Question:

Can you please tell me the assembled height of this product. I may have to order some spacers to accommodate my vehicle ride height. Thanks in advance.

asked by: Bill

0

Expert Reply:

The Timbren Active Off-Road Bumpstops # TABSOSR referenced in your question feature an assembled height of 4-5/8 inches. I have attached a short video review on this kit along with the written installation instructions that you can check out as well.

expert reply by: Chris R

0

click to enlarge

Answer 1

Hey Tarek, for your 2023 Ford Raptor I recommend checking out the Timbren Suspension Enhancement System #T75MR. This suspension enhancement system has a load leveling capacity of 3,000 lbs, will increase stability while reducing sag, and will install…

view full answer...

Answer 2

Hello Steve. I do have a good solution for you, but I cannot recommend using the Malone Adapter #MPG544. Since it is rated for towing only 4,000 lbs, your 8,000 lb towed vehicle would be double the max towing capacity. You are right about there being…

view full answer...

Answer 3

For your 2018 Toyota Tundra the suspension enhancement I recommend is the Timbren kit part #TABSOSR because this kit installs easily, gives you the suspension support you need to greatly reduce the sag, and because it doesn't require monitoring…

view full answer...

Answer 4

I went out and pulled both the Timbren kit part #TTORTUN4 and #TTORTUN4L from our warehouse to measure them for you and found that they both sit exactly 3-3/4 inches tall.

view full answer...

Answer 5

When installing any Timbren system on the 2019 Toyota Tacoma you should have about 1/2" to 1-1/2" between the frame and the spring after installation. You won't necessarily be losing wheel travel when you use a Timbren Rear Suspension…

view full answer...

Answer 6

Hey Steve, what you would want is the Timbren kit part #TDDR05 that fits your 2006 Dodge Dakota. This will give your truck additional rear suspension support so that it doesn't sag when towing your travel trailer.

view full answer...

Answer 7

Overall height is 5-3/16 inches. That means that once installed, the double convoluted springs from the Timbren SES Kit, #TGMRCK25D, will sit 5-3/16 inches below the jounce bumper holder on the frame. The outer diameter of these springs is 4-5/16…

view full answer...

Answer 8

There is an interesting amount of Timbren kits that fit your 2022 Toyota Tacoma long bed. The part #TABSTRFK is a standard duty kit that comes with a U-bolt flip kit helps with ground clearance. #T72FR is a severe service kit for 3 leaf springs which…

view full answer...

Answer 9

I just spoke with my rep at Timbren. The height of the Timbren Suspension Enhancement System - Rear Axle Item #T62FR for your 2010 Toyota Tundra is 3 9/16 inches for the rubber spring portion and 1 5/16 inches for the bracket with a combined overall…

view full answer...

Answer 10

The Timbren Active Off-Road Bumpstops - Rear Suspension - 3,600 lbs #TABSTRFK have bump stops and mounts that are 5-1/2 inches tall overall and u-bolts that are 8-1/4 inches long and 3-3/4 inches on center. I've attached a photo to assist. These…

view full answer...

Answer 11

For the 2019 Chevy Colorado with diesel engine there are not any compatible air bag kits (as of April 2019) but we do have other suspension helper kits that can support the rear suspension when it is under the load of your 5000-lb trailer. Based on…

view full answer...

Answer 12

We have the Timbren kit part #T92MR which can provide up to 5,000 lbs of additional support that will work great to help level your enclosed trailer. This installs on both sides of the trailer but with the additional support on both sides it will…

view full answer...

Assembled Height of Timbren Active Off-Road Bumpstops # TABSOSR

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching