Is Shank Compatible with Reese Strait-Line Weight Distribution System

Question

Question:

Can Part # RP69FR be used with # RP66084? Thanks

asked by: Dave D

0

Expert Reply:

Yep, the Reese Weight Distribution Shank # RP69FR is 100% compatible with the Reese Strait-Line Weight Distribution System # RP66084.

expert reply by: Kyle S

0

Answer 1

The Curt #C72CR ball platform for the Rebellion XD will NOT fit on a weight distribution shank, as the channel isn't wide enough. The channel is about 1-1/2 inches wide, while a standard weight distribution shank is 2 inches in width. Adding a…

view full answer...

Answer 2

The Equal-i-zer Weight Dist Shank - 18" Long - 7" Rise, 3" Drop - 600 to 1,400 lbs TW #EQ90-02-4500 has the same hole spacing as the Curt Rebellion XD Hitch Ball Attachment #C72CR but that is the only similarity. They physically will…

view full answer...

Answer 3

Unlike most other weight distribution shanks out there the part #TLM9010 does not fit the standard dimensions like you are looking for. This has wider holes for the head to attach to that are spaced further apart. For a similar shank that has 9…

view full answer...

Answer 4

The Adjustable Drop Hitch Receiver Adapter - 2" Hitches - 11" Rise/Drop - 7,000 lbs #PH54FR is rated for a tongue weight of 700 lbs max. The Replacement 2" Receiver for Curt Multi-Ball Adjustable Ball Mount #C45802 will work with the…

view full answer...

Answer 5

Good question, and thankfully many weight distribution shanks from different manufacturers are interchangeable so long as they have the proper hole spacing. This Reese shank does have the correct hole spacing to work with the Curt TruTrack so yes,…

view full answer...

Answer 6

Yes, you are able to replace the 2-5/16" included with the Reese Dual Cam II Weight Distribution System #RP45FR with a 2" Ball #A-90. This will allow you to use the weight distribution on your 2022 Big Tex 60EC car hauler trailer with a…

view full answer...

Answer 7

One inch of preload is too much for the install of the SumoSprings kit part #TSS-107-40 that you referenced. You want between 1/4 and 1/2 inch of preload otherwise you'll have a harsher ride quality. If you have spacers installed you would need…

view full answer...

Answer 8

I measured the SumoSprings Trailer Helper Springs #TSS-107-40 and it will be either 6-3/4" with both spacers, 6-1/4" with one spacer, or 5-3/4" with no spacer when measured from the top of the U-Bolt plate to the top of the spring once…

view full answer...

Answer 9

I spoke with my contact at SuperSprings to find out if this would present any issues for you. Although the amount of compression you are describing with the #TSS-107-40 installed is not ideal, they assured me that the system would still work as…

view full answer...

Answer 10

Based on the information you provided you will need 2 sets of the SumoSprings Trailer Helper Springs #TSS-107-40 for your 2022 Forest River Surveyor Legend 202RBLE travel trailer. These springs are compatible with axles from 3,000-5,000lbs. Your…

view full answer...

Answer 11

While we do not have a video showing the installation of the line relocation kit that comes with the SumoSprings Trailer Helper Springs #TSS-107-40, I have linked a video below that shows an example of when one will be needed and explains what the…

view full answer...

Answer 12

It appears that your u-bolt plate on your 2021 Grand Design Reflection 31MB, will work with the SumoSprings Trailer Helper Springs #SS26MV. The plate itself including the bends does not appear to be larger than 3/4" nor does the width appear to…

view full answer...

Is Shank Compatible with Reese Strait-Line Weight Distribution System

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching