How Does Atwood RV Carbon Monoxide and Propane Gas Detector # AT36681 Install

Question

Question:

can i mount directly on the wall or is a cutout required?

asked by: Chuck

1

Helpful Expert Reply:

The Atwood RV Carbon Monoxide and Propane Gas Detector # AT36681 was designed to fit into a cutout like what the picture I attached shows. The wires on the back would prevent it from being able to mount flush.

Wall cutout size: 3-9/16" long x 3-7/16" wide x 1" deep

expert reply by: Jameson C

1

click to enlarge

Answer 1

The part number you referenced is older but it was a propane and carbon monoxide detector like what the part #AT36681 is as well so this would be a suitable replacement.

view full answer...

Answer 2

We do carry universal hitches that are rated for 10,000 pounds and above, like the Draw-Tite part #41990-07. I've linked the selection. With that being said a lot of times when a motorhome is rated for 5,000 pounds towing it isn't the hitch…

view full answer...

Answer 3

If you are looking for a trailer hitch to mount on your RV then the highest rated capacity is the Curt Trailer Hitches parts #C13702 and #C13701 which are both rated for a max of 6,000 lbs towing when a weight distribution (WD) system is used. These…

view full answer...

Answer 4

The motor you'd looked at, part #BVD0218-00 is the correct replacement for your range hood. I've confirmed this by forwarding your photo to the folks at Ventline.

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 8

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 9

Personally I wouldn't go with Timbren's for your needs. They're essentially rubber bump stops that prevent your suspension from flexing when weights placed on the rear of your Canyon. The major issue with them is comfortability when you…

view full answer...

Answer 10

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 11

Thanks for the pictures! 2" hitches do not all have a 5,000 lbs capacity. The capacity varies by vehicle. That is an old Reese 06497 hitch and the sticker is correct. It does indeed top out at 3,500 lbs. It looks like this hitch came on all of…

view full answer...

Answer 12

I was able to get a dimension sheet from my contact at Curt for the Curt Hitch part #C15800 that you referenced. See attached pic. I also attached a set of the installation instructions for this hitch.

view full answer...

How Does Atwood RV Carbon Monoxide and Propane Gas Detector # AT36681 Install

Continue Researching