Bearings and Seal for Replacing UFP Dexter 41062 Hub with Kodiak Hub and Rotor

Question

Question:

I have a marine trailer with ufp hubs 41062 and just bought kodiak hub KHR1389D and this bearing set DBRKHW85G first off will this work to replace my current hub? And also do I need races for what I have bought ?

asked by: Samuel N

0

Expert Reply:

I spoke with my contact at UFP Dexter and he said that your 41062 hub uses inner bearing 031-030-02, outer bearing 031-032-02, and seal 010-181-00. This is the equivalent of inner bearing # 25580, outer bearing # LM67048, and grease seal # GS-2125DL which can all be found in the bearing kit # BK3-310 along with the races for the bearings. Unfortunately the bearing kit # DBRKHW85G that you purchased isn't the same as the grease seal has a slightly larger diameter but that can easily be fixed.

If you are wanting to use the Kodiak 13" Hub and Rotor # KHR1389D on your current setup though all you need are the grease seals # RG06-090 which have the smaller inner diameter and the races # 25520 and # 02420. Please note that this hub and rotor has an 8 lug pattern whereas your current hub has a 6 lug pattern.

Please note that you'll want to make sure that what you do to one side of your axle that you do to the other side of your axle so that you have the safest ride possible and to reduce uneven stress on your suspension.

expert reply by: Jon G

0

Eddie S.

7/29/2020

Hello, I have a UFP 41062 hub that has a 2.125 x 3.371 x 0.500 oil seal, what would be the part number for that seal and what type of oil lube would I use? Thanks

Reply

Jon G.

8/7/2020

Part number is # GS-2125DL for a single seal or # RG06-090 if you need two of them. For the oil lube use part # XLPROLUBE. If this doesn't match what you already have then you'll want to clean out your hub just to make sure there won't be any kind of compatibility issue.

Reply

Answer 1

I looked up as much as I could on your 2018 Van Leigh 365RL Vilano and wasn't able to get the exact size. It's either going to be 1/2 inch or 9/16 inch based on what I was able to find on the bolt pattern. For 9/16 inch we have the part…

view full answer...

Answer 2

If you already have the housing welded on, you do not need the #DX63FR Dexter DX7.5L A-60 Brake Actuator w Electric Lockout. What you are looking for is the inner member. The #DX39FR Replacement Inner Member for Dexter DX7.5L Actuator - Single Axle…

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

A BT8 spindle would have a diameter of .99 of an inch where the bearings would both install and would have a diameter of 1.24 where the great seal would ride. That would require a hub part #AKIHUB-440-2-1K for an idler hub. A BTR spindle would have…

view full answer...

Answer 5

To determine the size of the hub assembly you need to purchase you have to determine which bearings are in the old assembly. If the old assembly has L44649 inner bearings, you would use the hub you chose #8-258-5UC1. If the inner bearings are marked…

view full answer...

Answer 6

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 7

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Answer 8

Based on the GVWR of your 2019 Jayco North Point 315RLTS it does seem like you have 7k axles. I recommend verifying this information to be sure. These axles typically use the #14125A outer and #25580 inner bearing found in the Timken #TMK92VR.…

view full answer...

Answer 9

The UFP H-1377 correlates to a Dexter #84 spindle, which is for a 3,500 pound axle. This will utilize an inner bearing #L68149 and an outer bearing #L44649. As this is being used on a boat trailer, I highly suggest going with the etrailer.com…

view full answer...

Answer 10

The inner diameters of the LM67048 and 15123 both are the same (1.250 inches). That means that a hub with either bearing in the outer bearing would fit your spindle. The part #AKHD-655-6-EZ-K would fit your axle.

view full answer...

Answer 11

After you've packed the bearings and assembled everything, carefully slide the hub assembly onto the spindle and install the outer bearing. Install the spindle and tang washer and run the spindle nut down finger tight, then rotate the hub back…

view full answer...

Answer 12

You can verify that the 10-19 grease seal included in Bearing Kit #BK2-100 is the correct one for your spindles by taking two measurements. First you want to measure the rear hub bore where the seal is inserted. The seal's outer diameter needs to…

view full answer...

Bearings and Seal for Replacing UFP Dexter 41062 Hub with Kodiak Hub and Rotor

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching